Bedienungsanleitung Makita UB 140D (Seite 5 von 56) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

448666

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely discharged.

Always stop tool operation and charge the battery cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room temperature at 10°C – 40°C (50°F – 104°F).

Let a hot battery cartridge cool down before charging it.

4. Charge the Nickel Metal Hydride battery cartridge when you do not use it for more than six months.

Blowing (Fig. 3)

For dust blowing, attach the nozzle to blower outlet, turn-

ing clockwise to lock it in place.

Dust suction (Fig. 4 & 5)

For dust suction, fit nozzle onto suction inlet and dust

bag onto blower outlet.

After the bag fills with dust, empty the contents of the

dust bag into a dust bin by releasing the fastener.

CAUTION:

Empty the dust bag before it becomes too full, or the suc-

tion force weakens.

Switch action (Fig. 6)

CAUTION:

Before inserting the battery cartridge into the tool, always

check to see that the switch trigger actuates properly and

returns to the “OFF” position when released.

To start the tool, simply pull the trigger. Tool speed is

increased by increasing pressure on the trigger. Release

the trigger to stop.

Air volume adjusting dial (Fig. 6)

Air volume can be adjusted to any of three settings by

turning the adjusting dial with the switch trigger fully

depressed. Refer to the table below for the relationship

between the number on the dial and the air volume.

CAUTION:

• Use the adjusting dial only after the switch trigger

returns to the “OFF” position. Turning the dial before

the trigger returns may damage the tool.

• If the tool is operated continuously until the battery car-

tridge has discharged, rest the tool for at least 15 min-

utes before proceeding with a fresh battery.

Installing set plate (Fig. 7)

For UB120D

Always install the set plate when using battery cartridges

1200, 1202 or 1202A. Install the set plate on the tool with

the screw provided as shown in Fig. 7.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work on

the tool.

Cleaning (Fig. 8)

From time to time, wipe off the outside of the tool using a

cloth dampened in soapy water. Never use gasoline, thin-

ner or the like, or discoloration and/or cracks can take

place.

To maintain product safety and reliability, repairs, mainte-

nance or adjustment should be carried out by a Makita

Authorized Service Center.

Number on the dial Air volume

3 High

2Medium

1Low

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita UB 140D Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita UB 140D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info