Bedienungsanleitung Makita UC 4020 (Seite 9 von 100) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

78298

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

................ Withdraw the mains plug!

................ First aid

........ Maximum permissible length of cut

...... Direction of chain travel

................ Chain oil

.................. Chain brake released

................. Chain brake applied

................ Prohibited!

............. Only for EU countries

Do not dispose of electric equipment

together with household waste material!

In observance of European Directive

2002/96/EC on waste electrical and

electronic equipment and its

implementation in accordance with

national law, electric equipment that have

reached the end of their life must be

collected separately and returned to an

environmentally compatible recycling

facility.

Intended use

ENE031-1

The tool is intended for cutting lumbers and logs.

Power supply

ENF002-1

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

For public low-voltage distribution systems of

between 220 V and 250 V.

ENF100-1

Switching operations of electric apparatus cause voltage

fluctuations. The operation of this device under

unfavorable mains conditions can have adverse effects to

the operation of other equipment. With a mains

impedance equal or less than 0.35 Ohms it can be

presumed that there will be no negative effects. The

mains socket used for this device must be protected with

a fuse or protective circuit breaker having slow tripping

characteristics.

General Power Tool Safety

Warnings GEA010-1

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and

instructions for future reference.

Chain saw safety warnings

GEB037-6

1. Keep all parts of the body away from the saw

chain when the chain saw is operating. Before you

start the chain saw, make sure the saw chain is

not contacting anything. A moment of inattention

while operating chain saws may cause entanglement

of your clothing or body with the saw chain.

2. Always hold the chain saw with your right hand on

the rear handle and your left hand on the front

handle. Holding the chain saw with a reversed hand

configuration increases the risk of personal injury and

should never be done.

3. Hold the power tool by insulated gripping surfaces

only, because the saw chain may contact hidden

wiring or its own cord. Saw chains contacting a “live”

wire may make exposed metal parts of the power tool

“live” and could give the operator an electric shock.

4. Wear safety glasses and hearing protection.

Further protective equipment for head, hands,

legs and feet is recommended. Adequate protective

clothing will reduce personal injury by flying debris or

accidental contact with the saw chain.

5. Do not operate a chain saw in a tree. Operation of a

chain saw while up in a tree may result in personal

injury.

6. Always keep proper footing and operate the chain

saw only when standing on fixed, secure and level

surface. Slippery or unstable surfaces such as

ladders may cause a loss of balance or control of the

chain saw.

7. When cutting a limb that is under tension be alert

for spring back. When the tension in the wood fibres

is released the spring loaded limb may strike the

operator and/or throw the chain saw out of control.

8. Use extreme caution when cutting brush and

saplings. The slender material may catch the saw

chain and be whipped toward you or pull you off

balance.

9. Carry the chain saw by the front handle with the

chain saw switched off and away from your body.

When transporting or storing the chain saw

always fit the guide bar cover. Proper handling of

the chain saw will reduce the likelihood of accidental

contact with the moving saw chain.

10. Follow instructions for lubricating, chain

tensioning and changing accessories. Improperly

tensioned or lubricated chain may either break or

increase the chance for kickback.

11. Keep handles dry, clean, and free from oil and

grease. Greasy, oily handles are slippery causing loss

of control.

12. Cut wood only. Do not use chain saw for purposes

not intended. For example: do not use chain saw

for cutting plastic, masonry or non-wood building

materials. Use of the chain saw for operations

different than intended could result in a hazardous

situation.

13. Causes and operator prevention of kickback:

Kickback may occur when the nose or tip of the guide

bar touches an object, or when the wood closes in and

pinches the saw chain in the cut. Tip contact in some

cases may cause a sudden reverse reaction, kicking

the guide bar up and back towards the operator.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita UC 4020 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Makita UC 4020

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info