Bedienungsanleitung Makita UM600D (Seite 17 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Türkisch)

690687

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

17 ENGLISH

►Fig.34: 1. Screws

8. Placetheundercoversothat

on the under-

cover is aligned with on the lock lever.

►Fig.35

9. While pressing the undercover, turn it clockwise

until

on the undercover is aligned with on the lock

lever.

►Fig.36

10. Makesurethatthelocklevertsinthegrooveon

the undercover.

►Fig.37: 1. Lock lever

CAUTION: Never use the tool without install-

ing the undercover.

11. Removethebladecover,andthenturnonthetool

to check that it works properly.

NOTICE: If the shear blades do not operate prop-

erly, the blades are not engaging the crank prop-

erly. Remove the blades and install them again.

Installing or removing the chip

receiver

Optional accessory

CAUTION: When installing or removing the

chip receiver, always wear gloves and attach the

blade cover so that your hands and face do not

directly contact the blade.

Thechipreceivergathersdiscardedleavesandmakes

clean-upafterwardmucheasier.Itcanbeinstalledon

eithersideofthetool.

Toinstallthechipreceiver,pressitagainsttheshear

bladessothatthehookstintotheholesoftheshear

blades.

►Fig.38: 1. Hooks 2. Holes

Toremovethechipreceiver,presstheleversonboth

sides to release the hooks.

►Fig.39: 1. Levers

NOTICE: Never try to remove the chip receiver

by an excessive force with its hooks locked in the

holes of the blades.

OPERATION

WARNING: Before shearing, clear away sticks

and stones from the shearing area. Furthermore,

clear away any weeds from the shearing area in

advance.

►Fig.40

WARNING: Keep hands away from blades.

CAUTION: Avoid operating the tool in very

hot weather as much as practicable. When operat-

ing the tool, be careful of your physical condition.

Shearing (for grass shear)

Turnthetoolonafteradjustingtheshearingheightand

holditsothatthebottomofthetoolrestsontheground.

Gentlymovethetoolforward.

►Fig.41

Whentrimmingaroundcurbs,fencesortrees,movethe

toolalongthem.Becarefulthatthebladesdonotcome

into contact with them.

►Fig.42

Whentrimmingsproutsorfoliageofasmalltree,trim

littlebylittle.

►Fig.43

Trimlargebranchestothedesiredheightusingbranch

cuttersbeforeusingthistool.

NOTICE: Do not use the tool in a way that causes

the motor to stop or to rotate extremely slowly.

NOTICE: Do not attempt to cut thick branches.

NOTICE: Do not allow the shear blades to con-

tact the ground during operation. The blades will

be dulled, causing poor performance.

NOTICE: Do not trim the wet grass or foliage of

small trees.

Cutting long lawn

Do not try to cut long grass all at once. Instead, cut the

lawninsteps.Leaveadayortwobetweencutsuntilthe

lawnbecomesevenlyshort.

►Fig.44

NOTE: Cutting long grass to a short length all at once

may cause the grass to die.

Trimming (for hedge trimmer)

CAUTION: Be careful not to accidentally

contact a metal fence or other hard objects while

trimming.Thebladesmaybreakandcauseaninjury.

CAUTION: Be careful not to allow the shear

blades to contact the ground.Thetoolmayrecoil

andcauseaninjury.

CAUTION: Overreaching with a hedge trim-

mer, particularly from a ladder, is extremely

dangerous. Do not work while standing on anything

wobblyorinrm.

NOTICE: Do not attempt to cut branches thicker

than 10 mm in diameter with the tool.Cutbranches

tothedesiredheightusingbranchcuttersbefore

using the tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Makita UM600D Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info