Bedienungsanleitung Makita UR3502 (Seite 12 von 29) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch)

691023

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

Nylon cutting head (Fig. 3)

NOTICE:

• Donotattempttobumpfeedtheheadwhilethetoolis

operatingatahighRPM.BumpfeedingatahighRPM

maycausedamagetothenyloncuttinghead.

• Thebumpfeedwillnotoperateproperlyiftheheadis

notrotating.

NOTE:

• Standard accessory varies depending on the model

andcountry.

The nylon cutting head is a dual grass trimmer head

providedwithabump&feedmechanism.

Tofeedoutthenyloncord,bumpthecuttingheadagainst

thegroundwhilethecuttingheadisrotating.

NOTE:

• Ifthenyloncorddoesnotfeedoutwhilebumpingthe

head, rewind/replace the nylon cord by following the

proceduresdescribedunder“Maintenance.”

Cable holder (Fig. 4)

Makeasmallloopofpowercable,andhangitontothe

cableholder.

ASSEMBLY

WARNING:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Failureto switchoffandunplugmayresultin serious

personalinjuryfromaccidentalstart-up.

• Never start the tool unless it is completely

assembled. Operation of the tool in a partially

assembledstate mayresultinseriouspersonal injury

fromaccidentalstart-up.

Installing the handle (Fig. 5)

WARNING:

• Do not remove or shrink the spacer or cushion. The

spacerkeepsacertaindistancebetweenbothhands.

Setting the grip/barrier assembly close to the other

gripbeyondthelengthofthespacermaycauselossof

controlandseriouspersonalinjury.

Fitthehandleandthebarrierontotherubberpartonthe

shaft pipe.Adjust the location of the handle, and then

tightenthemwithfourbolts.

Approved combination of cutting tool and

protector

WARNING:

• Always use the tool with the approved combination

of the safety equipments. Otherwise contact with a

cuttingtoolmaycauseseriousinjury.

• Never use the tool without the guard illustrated in

place. Failure to do so can cause serious personal

injury.

NOTE:

• Standard accessory varies depending on the model

andcountry.

For cutter blade (Fig. 6)

For nylon cutting head (Fig. 7)

Installing the protector for cutter blade (Fig. 8)

1. Aligntheholesontheinnerprotectorandtheholes

ofthegearcase.

2. Thentightenthemwiththreebolts.

Installing the protector for nylon head

CAUTION:

• Takecarenottoinjureyourselfonthecutterforcutting

thenyloncord.

• Do not forget to remove the cutter protector before

using.

1. Alignthefourboltsontheouterprotectoralongthe

holesontheinnerprotector.(Fig. 9)

2. Tightenthemwiththefourbolts.

3. Aligntheholesontheinnerprotectorandtheholes

ofthegearcase.

4. Tightenthemwithbolts.(Fig. 10)

Installing the cutter blade

WARNING:

• The outside diameter of the cutter blade must be

230 mm. Neveruseanyblade exceeding230mmin

outsidediameter.

CAUTION:

• Thecutterblademustbewellpolished,freeofcracksor

breakage.Polishorreplacethecutterbladeeverythree

hoursofoperation.

• Alwaysweargloveswhenhandlingthecutterblade.

• Alwaysattachthebladecoverwhenthetoolis notin

useorisbeingtransported.

• The cutter blade-fastening nut wears out in course

oftime. Ifthere appearsanywearordeformation on,

replace the nut. Ask your local authorized service

centertoorderit.

NOTICE:

• Besuretousegenuinecutterblade.

Turn the tool upside down so that you can replacethe

cutterbladeeasily.(Fig. 11)

1. Fitthereceivewasherontheaxis.

2. Turnthereceivewasheruntilthenotchonthereceive

washercomesonthenotchofthegearcase.

3. Insert the round bar through both notches so that

receivewashercannotbeturned.

4. Putthebladeonthereceivewasher.

5. Puttheclampwasherontheblade.

6. Putthecupontheblade.

7. Tighten them with the nut by turning it

counterclockwisewhileholdingtheroundbar.

To remove the blade, perform the above steps in

reverse.

Installing nylon cutting head (Fig. 12)

NOTICE:

• Besuretousegenuinenyloncuttinghead.

Turn the tool upside down so that you can replacethe

nyloncuttingheadeasily.

NOTE:

• Removethecoveronthecordcutterbeforeuse.

1. Fitthereceivewasherontheaxis.

2. Turnthereceivewasheruntilthenotchonthereceive

washercomesonthenotchofthegearcase.

3. Insert the round bar through both notches so that

receivewashercannotbeturned.

4. Fit the nylon cutting head by turning it

counterclockwise.

5. Remove the round bar after installing the nylon

cuttinghead.

To remove thenylonhead,performtheabovestepsin

revere.

Makita UR3502 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info