Bedienungsanleitung Makita VC3210L (Seite 9 von 68) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch)

598793

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Power supply

ENF001-1

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. This tool

should be grounded while in use to protect the operator

from electric shock. Use only three-wire extension cords

which have three-prong grounding-type plugs and three-

pole receptacles which accept the tool’s plug.

VACUUM CLEANER SAFETY

WARNINGS ENB119-5

WARNING! IMPORTANT READ CAREFULLY all

safety warnings and all instructions BEFORE USE.

Failure to follow the warnings and instructions may result

in electric shock, fire and/or serious injury.

1. Before use, make sure that this cleaner must be

used by people who have been adequately

instructed on the use of this cleaner.

2. Only use the socket outlet on the cleaner for

purposes specified in the instructions.

3. If foam/liquid comes out, switch off immediately.

4. Clean the water level limiting device regularly and

examine it for signs of damage.

5. Do not use the cleaner without the filter. Replace a

damaged filter immediately.

6. USE OF EXTENSION CORD. When using an

extension cord because of the great distance to

your power source, try to employ a cord that is

sufficiently thick but not too long, or cleaner

performance will be adversely affected. For

outdoor applications use an extension cord

suitable for outdoor use.

7. VOLTAGE WARNING: Before connecting the

cleaner to a power source (receptacle, outlet, etc.)

be sure the voltage supplied is the same as that

specified on the nameplate of the cleaner. A power

source with voltage greater than that specified for

the cleaner can result in SERIOUS INJURY to the

operator as well as damage to the cleaner. If in

doubt, DO NOT PLUG IN THE CLEANER. Using a

power source with voltage less than the

nameplate rating is harmful to the motor.

8. AVOID UNINTENTIONAL STARTING. Be sure

switch is OFF when plugging in.

9. Do not attempt to pick up flammable materials, fire

works, lighted cigarettes, hot ashes, hot metal

chips, sharp materials such as razors, needles,

broken glass or the like.

10. NEVER USE THE CLEANER IN THE VICINITY OF

GASOLINE, GAS, PAINT, ADHESIVES OR OTHER

HIGHLY EXPLOSIVE SUBSTANCES. The switch

emits sparks when turned ON and OFF. And so

does the motor commutator during operation. A

dangerous explosion may result.

11. Never vacuum up toxic, carcinogenic,

combustible or other hazardous materials such as

asbestos, arsenic, barium, beryllium, lead,

pesticides, or other health endangering materials.

12. Never use the cleaner outdoors in the rain.

13. Do not use close to heat sources (stoves, etc.).

14. GUARD AGAINST ELECTRIC SHOCK. Prevent

body contact with grounded surfaces. For

example; pipes, radiators, ranges, refrigerator

enclosures.

15. Do not block cooling vents. These vents permit

cooling of the motor. Blockage should be carefully

avoided otherwise the motor will burn out from

lack of ventilation.

16. Keep proper footing and balance at all times.

17. DO NOT ABUSE CORD. Never carry the cleaner by

cord or yank it to disconnect from receptacle.

Keep cord away from heat, oil, and sharp edges.

Inspect cleaner cords periodically and if damaged,

have repaired by authorized service facility.

Inspect extension cords periodically and replace if

damaged.

18. Do not fold, tug or step on the hose.

19. Stop the cleaner immediately if you notice poor

performance or anything abnormal during

operation.

20. DISCONNECT THE CLEANER. When not in use,

before servicing, and when changing accessories.

21. Clean and service the cleaner immediately after

each use to keep it in tiptop operating condition.

22. MAINTAIN THE CLEANER WITH CARE. Keep the

cleaner clean for better and safer performance.

Follow instructions for changing accessories.

Keep handles dry, clean, and free from oil and

grease.

23. CHECK DAMAGED PARTS. Before further use of

the cleaner, a guard or other part that is damaged

should be carefully checked to determine that it

will operate properly and perform its intended

function. Check for alignment of moving parts,

binding of moving parts, breakage of parts,

mounting, and any other conditions that may

affect its operation. A guard or other part that is

damaged should be properly repaired or replaced

by an authorized service center unless otherwise

indicated elsewhere in this instruction manual.

Have defective switches replaced by authorized

service center. Don’t use the cleaner if switch

does not turn it on and off.

24. REPLACEMENT PARTS. When servicing, use only

identical replacement parts.

25. STORE IDLE CLEANER. When not in use, the

cleaner should be stored indoors.

26. Be kind to your cleaner. Rough handling can

cause breakage of even the most sturdily built

cleaner.

27. Do not attempt to clean the exterior or interior with

benzine, thinner or cleaning chemicals. Cracks

and discoloration may be caused.

28. Do not use cleaner in an enclosed space where

flammable, explosive or toxic vapors are given off

by oil-base paint, paint-thinner, gasoline, some

mothproofing substances, etc., or in areas where

flammable dust is present.

29. Do not leave the cleaner cord lying on the floor

after you have finished a cleaning job. It can

become a tripping hazard or may cause damage to

the cleaner.

30. Do not operate this or any tool while under the

influence of drugs or alcohol.

31. As a basic rule of safety, use safety goggles or

safety glasses with side shields.

Makita VC3210L Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info