Bedienungsanleitung Manitowoc Q210 (Seite 27 von 40) (Englisch)

603229

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Section 4 Maintenance

Part Number 000001130 12/08 4-5

H. Remove the Bin Door

• Grasp the rear of the bin door and pull bin door

forward approximately 5”.

• Slide bin door to the rear while applying upward

pressure (The rear door pins will ride up into the track

slot and slide backward to the stop tab).

• While applying pressure against the bin door pull

down on the rear of each bin door track until the door

pins clear the stop tabs.

• Slide the rear door pins off the end and then below

the door track. Slide bin door forward allowing the

back of the door to lower into the bin. Continue

forward with the bin door until the front pins bottom

out in the track.

• Lift right side of door until the front pins clear the

track, then remove door from bin.

Step 7 Mix a solution of cleaner and warm water.

Depending on the amount of mineral buildup, a larger

quantity of solution may be required. Use the ratio in the

table below to mix enough solution to thoroughly clean

all parts.

Step 8 Use ½ of the cleaner/water solution to clean all

components. The cleaner solution will foam when it

contacts lime scale and mineral deposits; once the

foaming stops use a soft bristle brush, sponge or cloth

(not a wire brush) to carefully clean the parts. Soak the

parts for 5 minutes (15 – 20 minutes for heavily scaled

parts). Rinse all components with clean water.

Step 9 While components are soaking, use ½ of the

cleaner/water solution to clean all foodzone surfaces of

the ice machine and bin. Use a nylon brush or cloth to

thoroughly clean the following ice machine areas:

• Evaporator plastic parts – including top, bottom and

sides

• Bin bottom, sides and top

Rinse all areas thoroughly with clean water.

Step 10 Mix a solution of sanitizer and warm water.

Step 11 Use 1/2 of the sanitizer/water solution to

sanitize all removed components. Use a cloth or sponge

to liberally apply the solution to all surfaces of the

removed parts or soak the removed parts in the

sanitizer/water solution. Do not rinse parts after

sanitizing.

Step 12 Use 1/2 of the sanitizer/water solution to

sanitize all foodzone surfaces of the ice machine and

bin. Use a cloth or sponge to liberally apply the solution.

When sanitizing, pay particular attention to the following

areas:

• Evaporator plastic parts - including top, bottom and

sides

• Bin bottom, sides and top

Do not rinse the sanitized areas.

Step 13 Replace all removed components.

Step 14 Reapply power and water to the ice machine

and place the toggle switch in the WASH position.

TRACK SLOT

SLIDE DOOR

FORWARD

STOP TAB

PRESS DOWN

TO RELEASE

DOOR

Solution Type Water Mixed with

Cleaner 1 gal. (4 l) 16 oz (500 ml) cleaner

Solution Type Water Mixed With

Sanitizer 6 gal. (23 l) 4 oz (120 ml) sanitizer

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Manitowoc Q210 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info