Bedienungsanleitung Marantec Comfort 60 (Seite 14 von 24) (Englisch)

680458

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

14 Operating instructions, Comfort 50, 60 (#104172 – GB)

5.4.2 Checking the automatic cut-out

WARNING!

Danger of injury due to incorrectly programmed values for

the door driving power!

• Check the automatic cut-out function in the OPEN and CLOSE

directions.

Automatic cut-out in the OPEN direction

• During travel, apply a load of 20 kg to the door at the mid point of

the bottom edge of the door:

The door should stop immediately.

Automatic cut-out in the CLOSE direction

• Placeanobject,50mminheight,ontheoor.

• Drive the door towards the obstacle:

The operator system should stop and reverse when it touches the

obstacle.

The settings for the driving power in the OPEN and CLOSE directions

remain saved even if the mains power supply is interrupted.

The parameters are returned to the factory settings only after a reset.

➔“Menu 11 - RESET“

5.4.3 Checking the photocell

Photocell

• Check all the photocells individually by triggering them.

• Check all the photocells just before the door reaches the CLOSED

position.

Special points regarding door-frame photocells

– A door-frame photocell must function above the position at which

it is installed. Below the installation position, the function of the

photocell is suppressed by the control unit.

– If several photocells are connected, all the photocells function in

the same way as a door-frame photocell, if present.

5.5 Special programming

DANGER!

Danger of injury due to incorrect settings for the door

driving power!

The DIN EN 13241-1 and EN 12453 provide limits for the protection

of people. These can be exceeded by selecting the wrong parameters.

It is therefore essential to test the force generated by the door.

• Check the programmed parameter values.

➔“5.4.2 Checking the automatic cut-out“

• Havethedrivingforcetestedbyqualiedandtrained

professionals with a force tester designed for this purpose.

NOTICE

Material damage resulting from incorrect programming of

the door operator.

After a reset, all the parameters are returned to the factory settings.

Safety elements that are operational and are connected to the system

will be recognised anew after a reset.

To ensure that the controls functions properly:

• Reprogram all the required functions.

• Reprogram the remote control.

• Drive the operator system once to the OPEN position and then the

CLOSED position.

If a photocell is connected, it will be automatically detected by the

control system as soon as the power supply is connected.

The photocell can be reprogrammed later.

Photocells that are not required must be disconnected before the

power supply is connected; otherwise they will be recognised by the

controls.

➔“4.3.3 Terminal block XB03“

CHECK

A function test must be carried out after changes have been made in

programming mode.

➔“5.4 Function test“

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantec Comfort 60 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantec Comfort 60

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info