Bedienungsanleitung Marantec Comfort SU500F (Seite 5 von 52) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

742805

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

4 - PRODUCT INSTALLATION

4.1 - Installation

Before proceeding with the installation, check the integrity of the

product and that all components are present in the package.

Check that the gate weight respects the limit of the table (paragraph

2.2) and dimensions of the gear motor are met (Fig. 1).

Fig.2 shows a typical installation:

Gear motor (1)

Photocells (2)

Columns for photocells (3)

Flashing light with antenna (4)

Key switch or digital keypad (5)

Pressure-sensitive edge (6)

The automation system must be equipped with a pressure-sen-

sitive edge protecting all possible crushing points (hands, feet,

etc.) in accordance with the requirements of the EN 13241-1

standard.

They shall state that the installer shall check that the tempera-

ture range marked on the drive is suitable for the location.

ATTENTION !

4.2 - Installing the foundation box

Verify the orientation and the overall dimensions of the base plate, x

to ground the base-plate through 4 sturdy screw-anchors or drown it

into the concrete (Fig.3).

Provide one or more corrugated duct tubes for routing the electric

cables.

4.3 - Motor unlock

4.5 - Rack assembling

Open entirely the gate.

Put a rack element on the pinion gear and fasten it to the gate with

screw and spacing bars (Fig.10).

Move the gate manually bringing the pinion gear into line with the

last spacing bar.

Fasten the rack element for good.

4.6 - Limit switch xing

The exact dimensions of the rack must be known to allow pre-

cise calculation of the xing plate position.

With motors with integrated night lights (Night Light System)

make sure not to rip o󰀨 the cable that connects the leds on the

cover with the control board. If necessary, disconnect the con-

nector shown in gure 7.

The stop lock position must assure that the limit switch brackets

don’t collide with the pinion gear. (Fig.11)

For a correct positioning of the other elements and to assure their

straightness, it is necessary to employ a rack element using it as

support and reference. It is besides necessary to assure an aperture

of 2 mm between rack and pinion gear, so that the gate weight doe-

sn’t rest on the gearmotor pinion gear.

The gate has to be equipped with stop locks at the opening and

closing, which prevent the gate derailment.

Haul the gate manually at the opening leaving, depending on the

gate weight, a crack from 30 to 50 mm between the main gate and

mechanical stop.

Fasten the limit switch bracket through the dowels so that the limit

switch is pressed (Fig.11).

Follow the instructions of the control panel and close the cover.

4.4 - Fixing the plate

Open the cover by applying leverage with a screwdriver on the re-

cesses at the sides (Fig.6).

Place the gearmotor on the plate and x the 4 nuts (Fig.8a). If the

permitted adjustment of the rack is not su󰀩cient, before tightening

the nuts the height of the gearmotor can be corrected using the four

regulator stud bolts (Fig.8b).

After the adjustment, it is important to fully tighten the nuts, making

sure that the gearmotor is rmly anchored to the ground throughout

the gate’s travel stroke.

The screws should be tightened again after the gearmotor has been

operated a few times.

Replace the cover so that the light is pointed in the required direction

(Fig.9), such as towards the passage.

To release the gearmotor remove the cap on the side (Fig.4.1) and

turn the pin with the release key or the Sub remote control (Fig.4.2).

Then turn the lever (Fig.5).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantec Comfort SU500F Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info