Bedienungsanleitung Marantz 8000 (Seite 4 von 16) (Englisch)

522811

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

ENGLISH

FRANÇAIS

DEUTSCH

NEDERLANDS

ESPAÑOL

ITALIANO

PORTUGUÊS

SVENSKA

DANSK

FOREWORD

Be sure to read this section before any connection to the mains

supply.

WARNINGS

Never expose the amplifier to rain or moisture.

Never remove the amplifier’s cover.

Never insert anything into the amplifier’s vents.

Never handle the mains lead while your hands are wet.

EQUIPMENT MAINS WORKING SETTING

This Marantz product is available in two different variations, depend-

ing on geographical area. One variation has a preset mains voltage

(230V for General Europe model and U.K. model), while the other

variation features variable voltage that can be selected using a volt-

age selector on rear panel (110V, 120V, 220V, 240V).

The voltage selector must be set for your local mains voltage before

any connection to the mains supply. If you need to change its voltage

setting, consult your dealer your local Marantz service provider.

IMPORTANT: (FOR U.K. MODEL)

This apparatus is fitted with an approved moulded 13 Amp plug.

To change a fuse in this type of plug proceed as follows:

1. Remove fuse cover and fuse.

2. Fix new fuse which should be a BS1362 5A, A.S.T.A. or BSI ap-

proved type.

3. Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should be

cut off and an appropriate plug fitted in its place.

If the mains plug contains a fuse, this should have a value of 5A. If

a plug without a fuse is used, the fuse at the distribution board should

not be greater than 5A.

NOTE:

The severed plug must be destroyed to avoid a possible shock haz-

ard should it be inserted into a 13A socket elsewhere.

HOW TO CONNECT A PLUG (FOR U.K. MODEL)

The wires in the mains lead are coloured in accordance with the

following code:

BLUE— “NEUTRAL” (“N”)

BROWN—“LIVE” (“L”)

1. The BLUE wire must be connected to the terminal which is

marked with the letter “N” or coloured BLACK.

2. The BROWN wire must be connected to the terminal which is

marked with the letter “L” or coloured RED.

3. Do not connect either wires to the earth terminal in the plug which

is marked by the letter “E” or by the safety earth symbol or

coloured green or green-and-yellow.

Before replacing the plug cover, make certain that the cord grip is

clamped over the sheath of the lead—not simply over the two wires.

Recording and playback of any material may require previous con-

sent. Refer to the following for further information.

— Copyright Act 1956

— Dramatic and Musical Performers Act 1958

— Performers Protection Acts 1963 and 1972

— Any subsequent statutory enactments and orders

ABOUT THIS USER’S GUIDE

Figure numbers refer to the illustrations located at the back of this

User’s Manual. Numbers assigned to parts and controllers match

the callout numbers used inside the illustrations.

ALL UPPER-CASE BOLD type indicates the name of a connection

or controller as it is actually marked on the amplifier.

PRECAUTIONS

Note the following important precautions whenever operating the

amplifier.

SELECTING A LOCATION

Take a few moments to consider the following points before choos-

ing a place for the amplifier.

— Make sure ventilation holes are not blocked or covered.

— Ensure that air can circulate freely around the amplifier.

— Locate the amplifier on a surface that is free of vibration.

— Choose a place where the amplifier will not be exposed to inter-

ference from an external source.

— Avoid excessive heat, cold, moisture, and dust.

— Keep the amplifier out of direct sunlight.

— Do not locate the amplifier where it will be exposed to electro-

static charge.

GENERAL SAFETY PRECAUTIONS

— Never place heavy objects on top of the amplifier.

— Should foreign matter or water get into the interior of the amplifier,

immediately turn it off and contact your original dealer or Marantz

service provider.

— Never pull on the mains lead when unplugging the amplifier.

Grasp the plug itself.

— It is always a good idea to disconnect the amplifier from the

mains supply whenever leaving it unattended for long periods

or during thunderstorms.

CONNECTIONS

(Figure 1)

CONNECTING A TUNER

Connect the output jacks of your stereo tuner to the TUNER jacks of

this amplifier.

CONNECTING A COMPACT DISC PLAYER

Connect the output jacks of your CD player to the CD jacks of this

amplifier.

CONNECTING A TURNTABLE

Connect the L (Left) output cord of the turntable to the “L”PHONO

jack of this amplifier, and the R (Right) output cord to the “R”PHONO

jack. If the turntable has a ground wire, make sure you connect it to

the GND terminal of this amplifier. The GND terminal does not need

to be connected if the turntable does not have a ground wire.

CONNECTING A TAPE DECK

Connect the IN (recording input) jacks of the tape recorder to the

TAPE OUT jack of this amplifier, and the OUT (playback output)

jacks of the tape recorder to the TAPE IN jack.

CONNECTING A PROCESSOR

Connect the IN jacks of the processor to the PROCESSOR OUT

jack of this amplifier, and the OUT jacks of the processor to the

PROCESSOR IN jack. When not used, leave these jacks connected

with the supplied connecting pins.

CONNECTING A SPEAKER SYSTEM

You amplifier has two sets of SPEAKER SYSTEM terminals, which

means you can connect either one or two speaker systems.

NOTE:

Turn the kobes on the speaker terminals by hand. (Do not use a

tool to turn the knobs.)

• Connecting One Speaker System

Note the following points when connecting a single speaker system.

— The impedance of each speaker should be between 8 and 16

Marantz 8000 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info