Bedienungsanleitung Marantz CR601 (Seite 31 von 34) (Englisch)

37775

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

ENGLISH

TROUBLESHOOTING

If a problem should arise, first check the following.

1. Are the connections correct?

2. Have you operated the receiver according to the operating instructions?

3. Are the speakers and other components operating properly?

If this unit is not operating properly, check the items listed in the table below. Should the problem persist,

there may be a malfunction. Disconnect the power immediately and contact your store of purchase.

Symptom

Power does not turn on

when POWER

ON/STANDBY switch is

pressed.

There’s no sound

coming from the

speakers?

Sound is coming from

only one speaker?

Nothing happens when

remote control buttons

are pressed.

Cause

• Mains cord’s plug is not

plugged into wall outlet.

• The speaker cables are not

connected properly.

• The volume is set at minimum.

• The CR601 is muted.

• A pair of headphones is

connected.

• The wrong input source is

selected.

• A connecting cable may be

damaged.

• The other speaker’s cable is

not connected properly.

• Are the batteries dead?

• Is the remote control unit too

far away?

• Is there an obstacle between

the remote control unit and the

main unit?

• You have pressed the wrong

button.

• Batteries are not set in their

proper direction (ª and ·).

Measures

• Plug the mains cord in

properly.

• Check the speaker

connections and make sure

that none of the wires are

touching each other, other

connectors, or any metal parts.

• Turn up the volume.

• Unmute the CR601.

• Turn down the volume, then

disconnect the headphones .

• Check the input source setting.

• Check your connecting cables

for signs of damage and

replace as necessary.

• Check the speaker

connections and make sure

that none of the wires are

touching each other, other

connectors, or any metal parts.

• Replace the batteries with new

ones.

• Operate from closer to the

main unit.

• Remove the obstacle.

• Press the desired button.

• Set the batteries in the proper

direction.

Page

Symptom Cause Measures Page

Hissing noise is heard

on FM broadcasts.

Hissing or buzzing

sound is heard on AM

broadcasts.

Booming sound

(humming) is heard in

AM broadcasts.

Display says “Station

not Available”.

I can not access

secondary services.

I hear a burbling sound

on some stations.

Reception is noisy,

intermittent, and the

indicator

ﬂickers?

The radio presets no

longer work?

• A strong light source is

interfering with the CR601’s

remote sensor.

• Antenna cable is not properly

connected.

• Antenna is not pointing in the

right direction.

• Radio waves are weak.

• Noise from a TV or

interference in the signals sent

from the broadcast station.

• Signals transmitted over the

main cord are modulated by

the power source frequency.

• Ensure that DAB coverage

exists in your area.

• At the time of publishing this

manual not many secondary

services are available, this will

increase as more DAB stations

start broadcasting.

• DAB like other digital media is

good at producing quality

audio from a low level signal,

however if this signal, level is

too low a “burbling” sound can

sometimes be heard.

• You’re too far away from the

transmitter. Or, your FM

antenna is in the wrong

position or pointing in the

wrong direction. Or, the

station’s signal strength is

poor.

• The power cord has not been

connected to a wall outlet, or

the power has been turned off

for an extended period.

•

Make sure that the CR601 is

not subjected to direct sunshine

or inverter-type ﬂuorescent

lights. Relocate if necessary.

• Connect the leads properly.

• Point the antenna in the right

direction.

• Install an outdoor antenna.

• Turn off the TV.

• Change the position of the

loop antenna.

• Install an outdoor antenna.

• Insert the plug in the opposite

direction.

• Install an outdoor antenna.

• Check that antenna is

connected.

•

If a secondary service station is

available, “ >” will be displayed

in the “Ensemble No. & Freq.”

• Use the CR601’s “Tuning aid”

while repositioning your

antenna to get the maximum

signal strength and reduce this

noise.

• Switch the FM Mode to Mono.

• Adjust the position, height, and

direction of your FM antenna.

• Install an outdoor FM antenna,

preferably one with many

elements. Installing an out-

door antenna is a specialist’s

job, so contact your nearest

dealer for advice.

•

Preset your favourite radio

stations again. The power cord

must be plugged into a wall

outlet a few times each month

in order to preserve the presets.

CR601N_01 Eng 05.10.21 1:22 PM ページ27

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz CR601 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info