61654
35
Zoom out
Zoom in
Vorherige Seite
1/38
Nächste Seite
33
NAMES AND
FUNCTIONS
BASIC
CONNECTIONS
BASIC
OPERATIONS
BASIC
SETTINGS
PRACTICAL
CONNECTIONS
ADVANCED
OPERATIONS
IF YOU EXPERIENCE
PROBLEMS
MISCELLANEOUS
IF YOU EXPERIENCE
PROBLEMS
ENGLISH
IF YOU EXPERIENCE PROBLEMS
RADIO OPERATIONS
Symptom Possible Cause Resolution
Cannot select a broadcast station
by preset number.
The unit has lost all preset
information.
Register the broadcast station
again.
There is a lot of noise when
listening to an FM broadcast.
The signal of the broadcast station
being tuned is weak or reception is
poor in your area.
1. Change the orientation of the
antenna.
2. Try setting the FM stereo to FM
mono. (Page 22)
3. Change the FM antenna to a
commercially available outdoor
antenna.
Cannot automatically select FM
broadcast stations.
The signal of the broadcast station
being tuned is weak or reception is
poor in your area.
1. Change the orientation of the
simple antenna.
2. Try setting the FM stereo to FM
mono. (Page 22)
3. Change the FM antenna to a
commercially available outdoor
antenna.
Cannot automatically select AM
broadcast stations.
The AM loop antenna is not
connected correctly.
Connect the loop antenna correctly.
The signal of the AM broadcast
station is weak.
Refer to how to manually register a
broadcast station. (Page 21)
Display says “Station not available”.
Ensure that DAB coverage exists in
your area.
Check that antenna is connected.
I can not access Secondary
services.
At the time of publishing this
manual not many Secondary
services are available, this will
increase as more DAB stations start
broadcasting.
If a Secondary service station
is available, the SECONDARY
indicator will be displayed next to
the station name.
I hear a burbling sound on some
stations.
DAB like other digital media is good
at producing quality audio from a
low level signal, however if this
signal, level is too low a “burbling”
sound can sometimes be heard.
Use the unit’s “Tuning aid” while
repositioning your antenna to get
the maximum signal strength and
reduce this noise.
OPERATING EXTERNAL EQUIPMENT
Symptom Possible Cause Resolution
Audio from the external inputs
(AUX1 to AUX3) is not emitted.
The connections to external devices
are incorrect.
Refer to connecting external
devices. (Page 9)
The external device is not in play
mode.
Be sure to play media according to
the manual for the external device.
The input source is incorrect. Check the input source.
The audio volume of the external
device is low.
Increase the audio volume of the
external device.
The headphone jack has been
mistaken for the AUX1 jack.
Check the connector being used for
the connection.
Noise is being emitted from an
external device.
The cable being used to connect to
external is not connected securely.
Check cable connections.
M-CR502_T_DAB_01_ENG.indd 33M-CR502_T_DAB_01_ENG.indd 33 09.2.4 1:35:43 PM09.2.4 1:35:43 PM
35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Marantz M-CR502 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info