Bedienungsanleitung Marantz NR1403 (Seite 95 von 117) (Englisch)

522822

Zoom out

Zoom in

Vorherige Seite

1/117

Nächste Seite

GAudioH

Symptom Cause/Solution Page

Audio is not output. •Check the connections for all devices.

•Check the speaker connections and conﬁgurations.

•Check whether the audio device power is turned on.

•Adjust the master volume.

•Cancel the mute mode.

•Check the connection with the playback device and select the

proper input source.

•Match the input mode and the terminal assigned to be the digital

input terminal.

•Disconnect the headphones. No sound is output from the

speakers when headphones are connected.

9,10,13,

14,15,16,

17,18,19

45,46,47

–

The volume does not

increase.

•The maximum volume is set too low. Set the maximum volume

under “Limit” in the menu.

•Power for external devices connected to the output connectors

of the unit may not be turned on. Check the power of connected

external devices.

–

No sound is

produced from

surround speaker.

•Check if the surround speakers are connected to the SURROUND

terminals.

–

No sound is

produced from

subwoofer.

•Check the subwoofer connections.

•Turn on the subwoofer’s power.

•Set “Speaker Conﬁg.” – “Subwoofer” on the menu to “Yes”.

•If “Front” and “Center” for “Speaker Conﬁg.” are set to “Large”,

and “Subwoofer Mode” is set to “LFE”, no sound may be output

from the subwoofers, depending on the input signal or selected

sound mode.

45,46,47

–

DTS sound is not

output.

•Set “Decode Mode” on the menu to “Auto” or “DTS”.

Dolby TrueHD, DTS-

HD, Dolby Digital

Plus audio is not

output.

•Make HDMI connections.

Symptom Cause/Solution Page

Dolby PLg mode or

DTS NEO:6 mode

cannot be selected.

•Check that “Speaker Conﬁg.” – “Center” or “Surround” is set to

other than “None”. If the speaker system is 2.0/2.1ch, this sound

mode cannot be selected.

•When headphones are used, Dolby PLg or DTS NEO:6 cannot be

selected.

–

Audyssey MultEQ

Audyssey Dynamic

and Audyssey

Dynamic Volume

cannot be selected.

•Switch the sound mode to other than “DIRECT” or “PURE

DIRECT”.

•When headphones are used, Audyssey MultEQ

, Audyssey

Dynamic EQ

and Audyssey Dynamic Volume

cannot be

selected.

–

Audyssey Dynamic

and Audyssey

Dynamic Volume

cannot be selected.

•Run Audyssey

Setup.

M-DAX cannot be

selected.

•Check that an analog signal or PCM signal (Sample rate=44.1/48

kHz) is input. For playback of multichannel signals such as Dolby

Digital or DTS surround, M-DAX cannot be used.

•Switch the sound mode to other than “DIRECT” or “PURE

DIRECT”.

GFM/AM tunerH

Symptom Cause/Solution Page

Reception fails, or

there is a lot of noise

or distortion.

•Change the antenna orientation or position.

•Use an FM outdoor antenna.

•Separate the antenna from other connection cables.

Basic version

Advanced version

InformationsInformations

DVD

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz NR1403 Seite 95

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantz NR1403

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info