Bedienungsanleitung Marantz NR1501 (Seite 26 von 50) (Englisch)

453906

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

NAMES AND

FUNCTIONS

BASIC

CONNECTIONS

BASIC

OPERATION

ADVANCED

CONNECTIONS

SETUP

ADVANCED

OPERATION

TROUBLESHOOTING

OTHERSSETUP

ENGLISH

SETUP

3-1 AUTO SETUP

The unit's AUTO SETUP function automatically

measures the acoustic characteristics of the

speaker systems and listening room where the unit

is installed using the microphone provided, and sets

the optimum listening environment.

HOW TO OPERATE AUTO SETUP

During the measurement process, as the current

statuses will be displayed on the OSD menu screen,

turn on the monitor's power.

1. Connect the microphone provided to the

SETUP MIC jack on the front panel.

2. Position the microphone at the main

listening point.

Notes

• Place the microphone at the main listening point

before carrying out the measurements.

• With the microphone pointed straight up at the

ceiling at the listening point, use a stand or tripod

to adjust the microphone to the same height above

the ﬂ oor level as your ears.

• Be sure not to place any obstacles between the

speakers and microphone.

• When using a subwoofer with built-in ampliﬁ er,

set the volume control to the center position, and

set the crossover frequency to off or the highest

frequency.

• While the measurements are being performed,

do not stand between the microphone and either

speaker. Make the listening room as quiet as

possible. Dark noise may adversely affect the

indoor measurements. Close the windows, and

turn off the power of all devices (such as cell

phones, TV, radio, air conditioner, ﬂ uorescent

lights, electrical appliances or dimmers).

• During the measurement process, place your cell

phone at a distance from all the audio electronic

devices.

Cell phones, even when they are not being used,

may adversely affect the measurements due to

RFI (radio frequency interference).

• We recommend that the AUTO SETUP operation

be performed using the remote controller rather

than the front panel controls.

• The volume levels of the test tones played from

each channel will exceed the peripheral noise

in the listening environment and continue to

increase until the optimum signal-to-noise ratio

is attained.

• Proceed while taking the environment and any

nearby children into consideration.

3. Select SPEAKER SETUP on the MAIN

MENU, press the 3/4 cursor buttons to

select AUTO SETUP, and press the ENTER

button to display the start screen.

AUTO SETUP

BEFORE STARTING THE

SYSTEM PLEASE PLUG

THE MIC. IN USING

THE FRONT PANEL JACK

**WARNING**

THE TEST TONE IS LOUD

>START

RETURN TO MAIN MENU

4. Press the 3/4 cursor buttons to select

START, and press the ENTER button to start

the measurements.

When the measurements have been

completed, the screen shown below will

appear.

AUTO SETUP

COMPLETED

>APPLY CANCEL

To reflect the measurement results, move the

cursor to APPLY, and press the ENTER button. The

results that have been set by the AUTO SETUP can

be monitored on the menu setting screens shown

below.

• SPEAKER CONFIG (see page 22)

• SPEAKER DISTANCE (see page 23)

• SPEAKER CROSSOVER (see page 23)

• ROOM EQ SETUP (see page 23)

• CH LEVEL SETUP (see page 24)

3-2 MANUAL SETUP

When you want to set up the system to your

speciﬁ cations rather than using AUTO SETUP, set

the following items.

• SPEAKER CONFIG

• SPEAKER DISTANCE

• SPEAKER CROSSOVER

• ROOM EQ SETUP

• CH LEVEL SETUP

SPEAKER/R.EQ SETUP

>AUTO SETUP

SPEAKER CONFIG

SPEAKER DISTANCE

SPEAKER CROSSOVER

ROOM EQ SETUP

R RETURN TO SETUP MENU

1. Select SPEAKER SETUP from the MAIN

MENU.

2. Press the 3/4 cursor buttons to select an

item.

3. Press the ENTER button to enter what has

been selected.

4. Repeat steps 2 and 3 until all the settings

have been selected. Then press the 3/4

cursor buttons to select RETURN TO SETUP

MENU, and press the ENTER button.

SPEAKER CONFIG

>CENTER : YES

SURROUND : YES

SURR.B : 2CH

SUBWOOFER: YES

RETURN TO SETUP MENU

The conﬁ guration of the speakers connected to the

unit is set by following the steps below.

1. Press the 3/4 cursor buttons to select the

speakers of each channel.

2. Press the 1/2 cursor buttons to set whether

a speaker is to be selected (YES) or not

(NO).

CENTER:

Set whether the center speaker is to be selected

(YES) or not (NO).

SURROUND:

Select whether the surround left and right speakers

are to be selected (YES) or not (NO).

SURR. B:

Set the surround back left and right speakers.

2CH:

Select this when using the surround back left and

right speakers.

1CH:

Select this when using one surround back speaker.

The audio signals will be output from the SURR.-L

terminal. Check the connections.

NO:

Select this when not using both surround back left

and right speakers.

SUBWOOFER:

Select whether the subwoofer is to be selected

(YES) or not (NO).

3. When all the settings have been selected,

press the 3/4/1/2 cursor buttons to select

RETURN TO SETUP MENU, and press

the ENTER button to return to the menu

(SPEAKER/R.EQ SETUP).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz NR1501 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantz NR1501

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info