Bedienungsanleitung Marantz NR1501 (Seite 30 von 50) (Englisch)

453906

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

NAMES AND

FUNCTIONS

BASIC

CONNECTIONS

BASIC

OPERATION

ADVANCED

CONNECTIONS

SETUP

ADVANCED

OPERATION

TROUBLESHOOTING

OTHERS

ADVANCED

OPERATION

ENGLISH

ADVANCED OPERATION

AMP OPERATION

USING THE SLEEP TIMER

To program this unit for automatic standby, press

the SLEEP button on the remote controller.

Each press of the button will increase the time

before shut down in the following sequence.

OFF 10 12090603020

The sleep time will be shown for a few seconds in

the display on the front panel, and it will count down

until the time has elapsed.

When the programmed sleep time has elapsed, the

unit will automatically turn off.

Note that the

indicator on the display will illuminate

when the Sleep function is programmed.

To cancel the sleep function, repeatedly press the

SLEEP button on the remote controller until the

timer time is cleared. When it is canceled, the

indicator on the display goes off.

DISPLAY MODE

You can select the display mode for the front display

of the unit.

To select this mode, press the DISPLAY on the

remote controller or the front panel.

When this button is pressed, the display mode is

switched in the following sequence.

Input function → Volume → Surround → Input

signals → Input function

Input function:

The status of the input function that was set

in FUNCTION INPUT SETUP (see page 20) is

displayed.

Volume:

The current volume level is displayed.

Surround:

The status of the selected surround mode is

displayed.

Input signals:

The status of the signals that have been input to the

selected function is displayed.

DIMMER

When this button is pressed once, the display is

dimmed.

When this button is pressed twice, the display is

turned off and the indicator lights up.

Press this button again to turn the display on again.

Note

• In the display off status, only the indication on

the unit's display illuminates to indicate that this

function is operational.

RECORDING AN ANALOG SOURCE

In normal operation, the audio or video source

selected for listening through this unit is sent to the

record outputs.

This means that any program you are watching

or listening to may be recorded simply by placing

machines connected to the outputs for VCR OUT

in the record mode.

To record the input source signal you are

currently watching or listening to

1. Select the input source to record by turning

the INPUT SELECTOR knob on the front

panel or simply press the input selector

buttons on the remote controller.

The input source is now selected and you

may watch or listen to it as desired.

2. The currently selected input source signal

is output to the VCR OUT outputs for

recording.

3. Start recording to the recording component

as desired.

Notes

• When connecting only digital signal input, output

cannot be made to the VCR OUT terminals. When

using recording functions, be sure to also make

connections for analog signal input.

• No conversion is made from component video

signal input to Video signal output. Always use the

same signal type for both input and output.

• Video or audio signals input to HDMI input

terminals cannot be recorded.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz NR1501 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantz NR1501

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info