Bedienungsanleitung Marantz NR1501 (Seite 35 von 50) (Englisch)

453906

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

NAMES AND

FUNCTIONS

BASIC

CONNECTIONS

BASIC

OPERATION

ADVANCED

CONNECTIONS

SETUP

ADVANCED

OPERATION

TROUBLESHOOTING

OTHERS

ADVANCED

OPERATION

ENGLISH

REMOTE CONTROLLER

OPERATION

NORMAL MODE

WHEN OPERATING MARANTZ AV EQUIPMENT

PRODUCTS

This remote controller is preset with a total of 10

types of remote codes, including Marantz BD (Blu-

ray), GAME, DVD, VCR (VCR deck), DSS (satellite

broadcasting tuner), TUNER, CD, AUX1, AUX2, and

AMP (ampliﬁ er).

1. Press the SOURCE button.

For this example, press DVD.

Pressing the SOURCE button once changes

the remote control to the settings for the

source that was pressed.

To change the ampliﬁ er on other source,

press the SOURCE button twice (double-

click). The code is sent, and then the

ampliﬁ er source changes to DVD.

PRESET MODE

WHEN OPERATING NON-MARANTZ AV

EQUIPMENT PRODUCTS

This remote controller is preset with remote control

codes from AV equipment by other manufacturers.

The preset codes are TV, CD, DVD, BD and DSS.

Settings can be made in one of two ways.

When the preset codes are set, the following codes

are contained in the source button of the remote

controller.

See the attached manufacturer number list for the

preset manufacturers, devices, preset numbers,

and other settings.

Remote

controller

source name

Corresponding

preset code

Device name

TV TV Television

DVD DVD DVD player

CD CD CD player

DSS SATELLITE

Satellite

broadcasting

tuner equipment

Importants

• Some codes may be not match your equipment.

• The preset codes do not cover full functions.

• When the batteries are getting weak, the preset

procedure is not successful.

PROGRAMMING WITH THE 4-DIGIT CODE

Press and hold down the SOURCE button for

the appliance which should be controlled and

press SET button until the SEND indicator

blinks twice. Then SET indicator ﬂ ashes.

In case of TV, press and hold down the TV

Power On/off button and SET button.

Press the 4-digit code by numeric buttons for

appliance (code table at the end of this book)

When the procedure is successful, the

SEND indicator will blink twice.

Note

If the indicator did not blink twice, then repeat steps

1 through 2 and try entering the same code again.

SCANNING THE CODE TABLE

1. Switch on the appliance which should be

controlled.

2. Press and hold down the SOURCE button

for appliance which should be controlled

and press SET button until the SEND

indicator blinking twice. Then SET indicator

ﬂ ashes.

In case of TV, press and hold down the TV

Power On/off button and SET button.

3. Aim the remote control at the appliance

and slowly alternate between pressing

INPUT 3 button and the SOURCE ON/OFF

button for the appliance.

In case of TV, press INPUT 3 button and the

TV Power On/off button alternately.

4. Stop when the appliance turns off.

5. Press ENTER button once to lock in the

code.

CHECKING THE CODE

1. Press and hold down the SOURCE button

for appliance which should be controlled

and press SET button until the SEND

indicator blinking twice then SET indicator

ﬂ ashes.

In case of TV, press and hold down the TV

Power On/off button and SET button.

2. Press the INFO button.

The SEND indicator will blink twice.

3. To view the code for first digit, press 1

once.

Wait 3 seconds, count the SEND indicator

blinks (e.g. 3 blinks = 3) and write down the

number.

Note

If a code digit is “0”, the SEND indicator will not

blink.

4. Repeat step 3 three more times for

remaining digits. Use 2 for the second digit,

3 for the third digit, and 4 for the fourth

digit.

RESETTING THE CODE

1. Press and hold down the SOURCE button

for appliance which should be controlled

and press SET button until the SEND

indicator blinking twice.

Then SET indicator ﬂ ashes.

In case of TV, press and hold down the TV

Power On/off button and SET button.

2. Press the below codes to reset.

TV : 1000

DVD : 2000

CD : 3000

DSS : 4000

BD : 5000

The indicator will blink twice.

Note

After this procedure, the selected SOURCE button

is set initial code.

ADVANCED OPERATION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz NR1501 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantz NR1501

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info