Bedienungsanleitung Marantz NR1601 (Seite 13 von 84) (Englisch)

453907

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Basic version Advanced version Information

ENGLISHDEUTSCHFRANÇAISITALIANOESPAÑOLNEDERLANDSSVENSKA

Simple version

ENGLISHDEUTSCHFRANÇAISITALIANOESPAÑOLNEDERLANDSSVENSKA

Set up speakers (Audyssey

Auto Setup)

Step 3

Calculating

Step 4

Check

On the

Step 2

screen, use ui

to select “Calculate”, and then press

ENTER.

Measuring results are analyzed, and the

frequency response of each speaker in the

listening room is determined.

Step3:Calculating

MultEQ

Calculating

[----------]

Please wait...

• Analysis takes several minutes to complete. The

time required for this analysis depends on the

number of speakers connected.

The more connected speakers there are, the

longer it takes to perform analysis.

Remote control operation

buttons

Move the cursor

(Up/Down/Left/Right)

Conﬁrm the setting Return to previous menu

NOTE

• If the result differs from the actual connection

status, or if “Caution!” is displayed, see “Error

messages” (vpage10). Then carry out Audyssey

Auto Setup again.

• If the result still differs from the actual connection

status after remeasurement or the error message

still appears, it is possible that the speakers

are not connected properly. Turn this unit off,

check the speaker connections and repeat the

measurement process from the beginning.

• If you change speaker positions or orientation,

perform Audyssey Auto Setup again to ﬁnd the

optimal equalizer settings.

Use ui to select the item you want

to check, and then press ENTER.

Step4:Check

MultEQ

Please check the results

of the measured item.

Distance Check

Channel Level Check

Crossover Freq.Check

Speaker Config.Check

[ENT]:Select

• Subwoofers may measure a greater reported

distance than the actual distance due to added

electrical delay common in subwoofers.

• If you want to check another item, press

RETURN.

Use ui to select “Next” and then

press ENTER.

Step 5

Store

Use ui to select “Store” and then

press ENTER.

Save the measurement results.

Step5:Store

MultEQ

Storing

Please wait...

[----------]

Step5:Store

MultEQ

Store

Cancel

[ENT]:Store

Please select “Store”

to store measurement

values.

• Saving the results requires about 10 seconds.

• If you do not want to save the measurement

results, use ui to select “Cancel”, then select

“Yes” using o p. All the measured Audyssey

Auto Setup data will be erased.

NOTE

During saving of measurement results, be sure

not to turn off the power.

Finish

NOTE

After performing Audyssey Auto Setup, do not

change the speaker connections or subwoofer

volume. In event of a change, perform Audyssey

Auto Setup again.

Unplug the setup microphone from

the unit’s SETUP MIC jack.

Set Dynamic Volume

Finish

MultEQ

Storing complete.

Auto Setup is now

Turn on Dynamic Volume?

Yes : No

finished.

[ ]:Select [ENT]:Exit

• For details of Dynamic Volume settings, see

page 47.

n When turning Dynamic Volume on

• Use o to select “Yes”, and then press ENTER.

The unit automatically enters “Evening” mode.

n When turning Dynamic Volume off

• Use p to select “No”, and then press ENTER.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz NR1601 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantz NR1601

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info