Bedienungsanleitung Marantz NR1601 (Seite 77 von 84) (Englisch)

453907

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Basic version Advanced versionSimple version

ENGLISHDEUTSCHFRANÇAISITALIANOESPAÑOLNEDERLANDSSVENSKA

Information

ENGLISHDEUTSCHFRANÇAISITALIANOESPAÑOLNEDERLANDSSVENSKA

GHDMIH

Symptom Cause/Solution Page

No audio is

output with HDMI

connection.

• Check the connection of the HDMI connectors.

• When outputting HDMI audio from the speakers, set “HDMI

Audio Out” on the menu to “Amp”.

• When outputting HDMI audio from a TV, set “HDMI Audio Out”

on the menu to “TV”.

No video is

output with HDMI

connection.

• Check the connection of the HDMI connectors.

• Set the input source to match the connected HDMI connector.

• Check whether the TV is compatible with copyright protection

(HDCP). If connected to a device not compatible with HDCP, video

will not be output correctly.

14, 21

When the following

operations are

performed on

devices compatible

with HDMI control,

the same operations

occur on this unit.

• Power ON/OFF

• Switching audio

output devices

• Adjust volume

• Switch input source

• Set “HDMI Control” on the menu to “OFF”. To operate power

only for each device, set “Power Off Control” to “OFF”.

35, 51

GRadioH

Symptom Cause/Solution Page

Reception fails, or

there is a lot of noise

or distortion.

• Change the antenna orientation or position.

• Separate the AM loop antenna from the unit.

• Use an FM outdoor antenna.

• Separate the antenna from other connection cables.

GiPodH

Symptom Cause/Solution Page

iPod cannot be

played.

• Check the iPod connections.

• Switch the input source to “USB”.

• Incompatible iPod types cannot be played back.

“Connection Error”

is displayed.

• Unable to communicate properly. Turn off the power to this unit,

disconnect the iPod and then reconnect it.

–

“Not Support” is

displayed.

• The iPod connected to the unit is not compatible. Please make

sure the iPod you are connecting is compatible.

• The software version of the connected iPod is an old one. Please

update to the latest version.

–

“Connection Error”

is displayed.

• The iPod is not responding. Turn off the power to this unit,

disconnect the iPod and then reconnect it.

–

GUSB memory deviceH

Symptom Cause/Solution Page

When a USB

memory device is

connected, “USB” is

not displayed on the

menu.

• The set cannot recognize a USB memory device. Check the

connection.

• A USB memory device not conforming to mass storage class is

connected. Connect a USB memory device conforming to mass

storage class.

• A USB memory device cannot be connected via a USB hub.

–

Files on a USB

memory device

cannot be played.

• Set the USB memory device format to “FAT16” or “FAT32”. For

details, refer to the USB memory device’s operating instructions.

• If the USB memory device is divided into multiple partitions, only

ﬁles stored in the top partition can be played.

• The ﬁle is recorded in an incompatible format. Please record it in

a compatible format.

• This unit cannot play back ﬁles covered by copyright protection.

–

The ﬁle names

are not displayed

properly (“...”, etc.).

• Characters that cannot be displayed on this unit are replaced by

“.” (period).

The sound quality is

poor or there is noise

during playback.

• The ﬁle being played back has a low bit rate. –

“Connection Error”

is displayed.

• Unable to communicate properly. Turn off the power to this unit,

unplug the USB memory device and then plug it back in.

• The USB memory device is not responding. Turn off the power to

this unit, unplug the USB memory device and then plug it back in.

–

“Overcurrent” is

displayed.

• The USB memory device is consuming too much power. When

using a USB portable hard disk that can be powered by an AC

adapter, connect its AC adapter.

–

GM-XPortH

Symptom Cause/Solution Page

Audio is not output

when a wireless

receiver (RX101 is

connected).

• Check that the Bluetooth device and Wireless receiver (RX101)

are correctly paired.

–

GRemote control unitH

Symptom Cause/Solution Page

The set cannot be

operated with the

remote control unit.

• Batteries are worn out. Replace with new batteries.

• Operate the remote control unit within a distance of about 7 m

from this unit and at an angle of within 30°.

• Remove any obstacle between this unit and the remote control

unit.

• Insert the batteries in the proper direction, checking the q and

w marks.

• The set’s remote control sensor is exposed to strong light (direct

sunlight, inverter type ﬂuorescent bulb light, etc.). Move the set

to a place in which the remote control sensor will not be exposed

to strong light.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz NR1601 Seite 77

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantz NR1601

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info