Bedienungsanleitung Marantz PM-11S1 (Seite 15 von 29) (Englisch)

6528

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

ENGLISH

!1 PRE OUT Button

This button turns output from the PRE OUT jack on the

rear panel ON and OFF. When output is ON, the center of

the button is lit a blue color.

!2 REC OUT Button

This button turns the signals output from the RECORDER

1 and 2 OUT jacks on the rear panel ON and OFF. When

output is ON, the center of the button is lit a blue color. For

instructions on how to record, see “RECORDING” on pg.

16.

When RECORDER 1 is selected as the input source, sig-

nals are not output to the RECORDER 1 OUT jack. The

same goes for the RECORDER 2 OUT jack when RE-

CORDER 2 is selected as the input source.

!3 PHONO MC Button

This button switches the phono equalizer between MC and

MM. When MC is set, the center of the button is lit a blue

color. Set the phono equalizer amplifier according to the

type of cartridge you use.

!4 Side Illumination

The side illumination casts a blue light over switches and

buttons. It can be turned ON and OFF from the DISPLAY

button. For instructions on how to operate the side illumi-

nation, see “HOW TO OPERATE THE SIDE ILLUMINA-

TION” on pg. 18.

NAMES AND FUNCTIONS OF PARTS

DISPLAY

!5 Power Indicator

This indicator is lit a blue color while power to the PM-

11S1 is ON.

OPERATE

!6 Display Panel

Approximately 3 seconds after power

to the PM-11S1 is activated, the ID

set for the PM-11S1 is displayed here.

After that, the top line displays the in-

put source selected with either the IN-

PUT SELECTOR knob or the remote

controller, while the bottom line dis-

plays the volume level set with the

VOLUME knob or the remote control-

ler. When the PM-11S1 I is first activated, the attenuation

level (dB) is displayed for the initial volume level.

Volume Level Indication

The display panel also displays left-right level balance and

tone control trimming level. For instructions on how to ad-

just bass and treble, see “How to Trim Bass” and “How to

Trim Treble” on pg. 20.

The display panel also displays messages in response to

PM-11S1 operation.

!7 OPERATE Indicator

This indicator indicates the operating status of the PM-

11S1. When the ID is set to “0” for standalone operation, it

is lit a red color. When multiple PM-11S1s are connected

by FCBS, only the OPERATE indicator of the master PM-

11S1 (ID 1) lights a red color. Slave PM-11S1s whose

OPERATE indicator does not light a red color cannot be

used to operate other units in sync. For more information

on the FCBS, see “ABOUT FCBS” on pg. 17.

Also, the OPERATE indicator flashes if a protective circuit

trips. For troubleshooting procedures, see “TROUBLE-

SHOOTING” on pg. 22.

Max

0.5 dB steps

Min

Turn the VOLUME knob on

the PM-11S1 to the right or

press the VOLUME 3 button

on the remote controller.

Turn the VOLUME knob on

the PM-11S1 to the left or

press the VOLUME 4 button

on the remote controller.

PM-11S1N ENG(P09-P26)A4 04.8.17, 11:36 PMPage 11 Adobe PageMaker 6.5J/PPC

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz PM-11S1 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info