Bedienungsanleitung Marantz PM6010 OSE (Seite 2 von 10) (Englisch)

522813

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

English

GND (GROUND) TERMINAL

Connect the grounding wire from the turntable to this terminal.

TAPE CD-R/MD IN/OUT JACKS

Connect the play (output) jacks and record (input) jacks of tape decks

to these jacks.

Up to three tape decks can be connected.

NOTE:

When a surround processor or graphic equalizer is used, it must be

connected to the TAPE jacks.

SPEAKER SYSTEMS

Connect your speaker system to these terminals.

REMOTE CONTROL (BUS) TERMINALS

Another item of audio equipment with a remote control (bus) terminal can

be connected to these terminals by using a special-purpose cable. The

bus OUT terminal is used to send signals to another item of equipment.

The bus IN terminal is used to receive signals from another item of

equipment.

POWER CORD

Connect to a household power outlet.

POWER SWITCH

Pressing once switches the power ON, and pressing again switches it

OFF. The POWER indicator lights when the POWER switch is ON, and

go out when the POWER switch is OFF.

INPUT SELECTOR

Selects the program source to be recorded or played from the PHONO,

CD, TUNER, AUX.

VOLUME CONTROL

Adjusts the volume level. Turn the knob clockwise to increase the

volume.

You can also operate the amplifier with a remote control unit.

BALANCE CONTROL

Turn the knob to correct an unbalanced program source such as stereo

broadcast or to vary the output level of the left or right channel.

Note that, if the BALANCE control is turned fully in one direction, the

sound will not be heard from the speaker on the other side.

TAPE CD-R/MD SWITCHES

Press one of these switches to monitor the playback sound of a tape

deck connected to the rear panel of this unit.

When the CD-R/MD switch is pressed, this unit automatically enters the

tape dubbing mode, the COPY CD-R ﬁ TAPE indicator lights, and the

playback signal of CD-R or MD can be copied onto tape deck.

Set both of the switches to OFF when the CD-R or MD, tape decks are

not to be played.

For details, refer to "TAPE DECK OPERATION".

SOURCE DIRECT SWITCH

When this switch is pressed, the audio signal is supplied directly to the

volume control circuitry (the signal is directed through the minimum

required path to improve the reproduction of high-quality sources).

NOTE:

When this switch is ON, the settings of the tape monitor switches,

and balance control are ignored.

While this switch is depressed, recording, playback, or dubbing of

tapes cannot be carried out even when a tape monitor switch is

pressed.

IR SENSOR

The remote sensor receives the infrared commands from the remote

control unit. When an infrared signal is received from the remote control

unit. The remote control unit must always be pointed directly at the

remote sensor.

MUTING INDICATOR

Light up when the MUTING button in the remote control unit is pressed.

NOTE:

Be sure to check the VOLUME control setting before pressing this

switch to cancel muting, If the muting is canceled while the volume

setting is high, the speakers could be damaged.

PHONES JACK

Insert the standard phone plug of the headphones into this jack.

OPERATION PROCEDURES

TO PLAY AN ANALOG RECORD

1. Set the INPUT SELECTOR switch to PHONO.

2. Play a record on the turntable.

3. Adjust the volume with the VOLUME control.

NOTES:

• Set the VOLUME control to the minimum position before placing the

stylus on the record or before replacing the cartridge.

• Do not apply shock or vibration to the turntable during play, as this

may cause the stylus to jump and the analog record to be damaged.

• If the turntable is installed too close to the speakers, the volume may

not be able to be increased to a high level due to howling.

• Do not switch the power OFF while the stylus is on the record surface.

TO LISTEN TO FM/AM BROADCASTS

1. Set the INPUT SELECTOR switch to TUNER.

2. Tune in the desired station on the tuner.

3. Adjust the volume with the VOLUME control.

TO PLAY A COMPACT DISC

1. Set the INPUT SELECTOR switch to CD.

2. Play a CD on the CD player.

3. Adjust the volume with the VOLUME control.

TO PLAY A COMPONENT CONNECTED TO AUX JACKS

The component connected to the AUX jacks on the rear panel can be

played as follows.

1. Set the INPUT SELECTOR switch to AUX.

2. Play the component connected to the selected input.

3. Adjust the volume with the VOLUME control.

TAPE CD-R/MD

SOURCE DIRECT

INTEGRATED AMPLIFIER PM6010OSE

TAPE CD-R/MD

MUTE

MIN MAX

COPY

CD-R>TAPE

PHONO TUNER

AUX

INPUT SELECTOR VOLUME

BALANCE

POWER ON/OFF

PHONES

OFF

2 Operate each equipment to start play.

1 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz PM6010 OSE Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info