Bedienungsanleitung Marantz PS17 (Seite 16 von 44) (Englisch)

522805

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

ENGLISH

REAR PANEL CONNECTIONS

All connections to the rear panel should be made with the entire

system powered off.

To avoid errors, it is advisable to connect one cable at a time between

the various components.

[1] PHONO input / GND (GROUND)

terminal

Connect directly when the cartridge is MM (Moving Magnet) type.

Use the Step-up transfomer when the cartridge is MC (Moving Coil)

type.

And connect the grounding wire fom the Analog turntable to this

terminal.

[2] Three analog audio inputs

CD, TAPE/TUNER, and CD-R/MD :

Connect the audio outputs of your source components to the input

jacks on the amplifier.

[3] Two analog audio outputs for audio

source equipment

TAPE/TUNER and CD-R/MD :

Connect each output to the audio inputs (REC in) of your recording

equipment.

[4] Five analog audio inputs for video

source equipment

TV,LD,DVD, VCR1, and DSS/VCR2 :

Connect each input to the audio outputs of your video source

equipment.

[5] Two analog audio outputs for video

source equipment

VCR1, and DSS/VCR2 :

Connect each output to the audio inputs (REC in) of your video

recording equipment.

[6] Five video inputs

TV, DVD, VCR1, and DSS/VCR2 :

Connect each input to the video outputs of your video source

equipment.

[7] Five S-video inputs

TV, DVD, VCR1,and DSS/VCR2 :

Connect each input to the S-video outputs of your video source

equipment.

This unit's S-VIDEO input jacks support the S2 type. For details on

the screen mode of the wide-screen TV set that is connected

depending on the type of the external component's video system,

refer to the User Guide of the playback component and TV set which

are connected. These inputs are completely interchangeable with

the conventional S-VIDEO inputs.

[8] Two video outputs

VCR1, and DSS/VCR2 :

Connect each output to the video input (REC in) of your video

recording equipment.

[9] Two S-video outputs

VCR1, and DSS/VCR2 :

Connect each output terminals to S-video input (REC in) of your video

recording equipment.

[10]Two Component-video inputs

DVD, DSS,/VCR2 :

Connect the Y/Cr/Cb component video output of each your video

product to these jacks.

[11]Component Video Outputs

Connect these outputs to the component video inputs of a video

projector or monitor. When a source connected to one of the two

Component Video Inputs is selected the signal will be sent to these

jacks.

[12]Monitor. (VIDEO/S-VIDEO) output jacks

Connect this jack to the composite or S-Video input of a TV monitor or

video projector to view the on-screen menus and the output of any

standard video source selected by the receiver’s video switcher.

[13]Main Amplifier Inputs:

Connect the pre-output jacks of your pre-amp to these jacks at the

SEPARATE position of the system setup 1/2.

[14]Preamp Outputs (L, R, SL, SR, SBL,

SBR, C)

These jacks may be connected to an external power amplifier.

[15]SUB WOOFER output jack

Connect to the input jack(s) of the power amplifier for subwoofer

channel or powered subwoofer.

[16]6 CH INPUT jacks

Connect to the outputs of an external multichannel decoder or DVD

player with multichannel decoder.

[17]Six DIGITAL inputs

Dig.1,2,3 (coaxial) and Dig.4,5,6 (Optical)

Connect the digital output from a DVD player, HDTV receiver, LD

player or CD player to these jacks. The signal may be either a Dolby

Digital signal, DTS signal or a standard PCM digital source.

Note :

The coaxial connections are not for AC-3 RF from an LD, If you

want to decode this type of signal, an external demodulator must

be used.

[18]Digital Audio Outputs (Optical, Coaxial)

Connect these jacks to the matching digital input connector on a

digital recorder such as a CD-R or Mini Disc recorder.

[19]REMOTE CONT. IN/OUT terminals

Connect to a Marantz component equipped with remote control (RC-

5) terminals.

[20]Speaker Outputs terminals

Connect to the left and right speakers.

[21]AC INLET

Connect the provided detachable power cord, and connect the AC

plug to an unswitched AC wall output.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz PS17 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info