Bedienungsanleitung Marantz SR-4200 (Seite 14 von 31) (Englisch)

6556

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

ENGLISH

⁄7 CLEAR button

This button is used to cancel for certain memory or programming

operations.

⁄8 DIMMER button

When this button is pressed once, the display is dimmed.

When this button is pressed twice, the display is turned off and the

“DISPLAY OFF” indicator lights up.

Press this button again to turn on the display again.

⁄9 NIGHT button

Pressing this button prevents the Dolby Digital signal from playback at

a loud voice. This function reduces the voice by 1/3 to 1/4 at maximum.

Thus, it eliminates the occurrence of an abruptly loud voice at night.

However, the function is valid only for the case when the Dolby Digital

signal is entered into OPTICAL or COAXIAL and data to compress the

voice exists in the signal to be played back.

¤0 S- ( Source) DIRECT button

When this button is pressed, the tone control circuit is bypassed as

well as Bass Management.

¤1 SETUP / T.TONE button

Test tone function is used for adjusting the balance between the volume

levels of speaker channels. Press AMP button and press this button to

generate pink noise from each channel. Press the button again to stop

the pink noise generation.

¤2 OSD button

This button is not used for SR4200.

¤3 SLEEP (sleep timer) button

This button is used for setting the sleep timer. It can be operated the

same way as the button in unit.

¤4 TV VOLUME UP ( ) /DOWN ( ) buttons

These buttons increase or decrease TV’s volume.

PROGRAMMING THE REMOTE CONTROLLER

The remote controller RC5200SR must be programmed to use the

codes for your appliances of different brands. This is done by keying

in a 4-digit code or by scanning the codes until the correct one is found.

We recommend to using the 4-digit code. This mode is faster and

more reliable. The code scanning method should be used only if you

cannot find the code for one of your appliances. The codes are listed

at the end of this book.

Important:

Use the remote control buttons for programming, not the buttons of the

receiver or other appliances.

PROGRAMMING WITH THE 4-DIGIT CODE

1. Press and hold down the function button c for the appliance

which should be controlled and press SETUP ¤1 until the indicator

z blinks twice.

2. Press the 4-digit code for appliance (codetable at the end of this

book)

3. When the procedure is successful, the indicator will blink twice.

Notes:

If the indicator did not blink twice, then repeat steps 1 through 2

and try entering the same code again.

SCANNING THE CODE TABLE

1. Switch on the appliance which should be controlled.

2. Press and hold down the function button c for appliance which

should be controlled and press SETUP ¤1 until the indicator z

blinking twice.

3. Press the code 9 - 9 - 1.

The indicator will blink twice.

4. Aim the remote control at the appliance and slowly alternate

between pressing POWER x and the function button c for the

appliance.

5. Stop when the appliance turns off.

6. Press SETUP ¤1 once to lock in the code.

CHECKING THE CODE

1. Press and hold down the function button c for appliance which

should be controlled and press SETUP ¤1 until the indicator z

blinking twice.

2. Press the code 9 - 9 - 0.

The indicator will blink twice.

3. To view the code for first digit, press 1 once.

Wait 3 seconds, count the indicator blinks (e.g. 3 blinks = 3) and

write down the number.

Note:

If a code digit is “0”, the indicator will not blink.

4. Repeat step 3 three more times for remaining digits. Use 2 for the

second digit, 3 for the third digit, and 4 for the fourth digit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz SR-4200 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantz SR-4200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info