Bedienungsanleitung Marantz SR-4200 (Seite 24 von 31) (Englisch)

6556

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

ENGLISH

CAUSE

The power plug is not connected.

Mute is on.

The input cable is not connected correctly.

The master volume control is turned all the way down.

The function selector position is wrong.

The headphones are connected to the headphone jack.

Input cable connected incorrectly.

Speaker cable connected incorrectly.

The center speaker cable connection is incomplete.

STEREO has been selected for Surround mode.

Center = NONE has been selected in SETUP mode.

The surround speaker cable connection is incomplete.

STEREO has been selected for Surround mode.

Surround = NONE has been selected in SETUP mode.

Sub-woofer = NO has been selected in SETUP mode.

The headphones are connected to the jack.

Analog has been selected for input.

Surround mode is set to DOLBY.

The DVD or LD player is not DTS digital out capable.

Data error occurred during player skip.

The disc player is not 96kHz PCM digital out capable.

Surround mode is set to other than STEREO and AUTO.

Surround mode is set to DTS.

Nothing recorded on source.

Antenna connection is incomplete.

Reception is affected by other electrical fields.

The radio waves from the broadcasting station are weak.

Preset data has been erased.

Batteries are consumed.

Batteries are consumed..

Remote controller's function-key setting is wrong.

The distance between this SR4200 and the remote

commander is too far.

Something is blocking SR4200 and the remote commander.

SYMPTOM

SR4200 cannot be turned up.

No sound and picture are output

even when power is on.

Speaker does not outputting any

sound.

Sound and pictures from other

than equipment selected with the

function selector.

Sound from the wrong channel is

output from the speaker.

No sound is output from the center

speaker.

No sound is output from the

surround speakers.

No output to Sub Woofer Out.

Surround mode cannot be changed.

Noise is produced during DTS-

encoded CD or laser disc play.

DTS sources cannot be played.

Player skips during play of a DTS

source and produces noise.

A 96kHz PCM signal cannot be

played.

A normal PCM signal (CD or laser

disc) cannot be played.

A Dolby Digital signal cannot be

played.

A specific channel does not

produce output.

FM or AM reception fails.

Noise is heard during AM reception.

Noise is heard during FM reception.

Cannot get programmed station

when the PRESET button is

pressed.

Nothing appears on the remote

commander display.

Control with the remote control unit

fails.

REMEDY

Connect the power plug to the outlet.

Cancel mute using the remote control unit.

See the connection diagram and connect the cables correctly.

Adjust the master volume.

Select correct position.

Disconnect the headphones. (Speakers will not output sound when

headphones are connected.)

Connect the cable correctly by referring to the connection diagram.

Connect the cable correctly.

When STEREO is selected for Surround mode, no sound will be

output from the center speaker. Set another Surround mode.

Make the correct setting.

Connect the cable correctly.

When STEREO has been selected for Surround mode, no sound will

be output from the surround speaker. Set another Surround mode.

Make the correct setting.

Select Sub-woofer = YES.

Disconnect the headphones. (When headphones are connected,

Surround mode will be fixed to STEREO.)

Be sure to perform digital connection, select digital input, then play.

Select other mode.

Use a player which responds to DTS-digital out.

Set Surround mode to DTS.

Use a player that responds to 96kHz PCM digital out.

Set Surround mode to STEREO or AUTO.

Select other mode.

Check the encoded channel on the source side.

Correctly connect the indoor FM and AM antennas to FM and AM

antenna outlets.

Try changing location where the AM indoor antenna is set up.

Install an FM outdoor antenna.

Disconnecting power plug for long periods of time will erase preset

data. If that happens, input the preset data again.

Replace all the batteries with new ones.

Replace all the batteries with new ones..

Select different position from which equipment will be controlled.

Move closer to this SR4200.

Remove offending object.

TROUBLE SHOOTING

In case of trouble, check the following before calling for service:

1. Are the connections made properly ?

2. Are you operating the unit properly following user’s guide ?

3. Are the power amplifiers and speaker working properly ?

If the unit does not operate properly, check items shown in the following table.

If your trouble cannot be recovered with the remedy actions listed in

the following table, malfunction of the internal circuitry is suspected;

immediately unplug the power cable and contact your dealer, nearest

Marantz distributor or the Marantz Service Center in your country.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz SR-4200 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantz SR-4200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info