Bedienungsanleitung Marantz SR-4400 (Seite 9 von 36) (Englisch)

6562

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

ENGLISH

PROGRAMMING THE REMOTE

CONTROLLER

The remote controller RC5400SR must be

programmed to use the codes for your appliances

of different brands. This is done by keying in a 4-

digit code or by scanning the codes until the

correct one is found. We recommend to using the

4-digit code. This mode is faster and more

reliable. The code scanning method should be

used only if you cannot find the code for one of

your appliances. The codes are listed at the end of

this book.

Important:

• Use the remote control buttons for

programming, not the buttons of the receiver or

other appliances.

• Some codes may be not match your equipment.

In this case, your equipment cannot be

controlled with this remote controller.

PROGRAMMING WITH THE 4-DIGIT CODE

Press and hold down the function button for

the appliance which should be controlled and

press SETUP until the indicator blinks twice.

Press the 4-digit code for appliance (code

table at the end of this book)

When the procedure is successful, the

indicator will blink twice.

Note:

• If the indicator did not blink twice, then repeat

steps 1 through 2 and try entering the same code

again.

Numeric buttons 1 to 9 (A, B, C ... Z, –) /

Surround mode buttons

Numeric buttons

These buttons are used to enter figures in the selec-

tion of a tuner preset station and station name pre-

set or to set select a CD track number, etc. The func-

tions of these buttons are dependent on the function

button selected.

Surround mode buttons (when AMP mode is

selected)

These buttons are used to select the surround mode.

Note:

• The surround mode is set to 6-Stereo mode by

pressing M-CH ST button.

⁄0

P.SCAN (preset scan) button (when TUNER

mode is selected)

This button is used to start preset scan when

SR4400 is selected TUNER mode.

⁄1

0 / A/D button

0 button

This button is used to enter the number “0”

A/D button (when AMP mode is selected)

This is used to switch between the analog and

digital inputs.

⁄2

CONTROL buttons

These buttons are used when operating the CD

player, TAPE deck, etc.

The function of these buttons are dependent on the

function button selected.

For the controllable functions of each input function,

please refer to contrable function table on the page

⁄3

ATT (attenuator) button

When the input signal is too high and the voice dis-

torts even by throttling the SR4400 VOLUME con-

trol, turn on this function. “ATT” is indicated when

this function is activated.

The input level is reduced. Attenuator is invalid for

use with the output signal of “REC OUT”.

Note:

• This function is unavailable during the digital

input is selected.

⁄4

TREBLE UP ( ) /DOWN ( ) buttons

These buttons are used to adjust the tone control of

high frequency sound for left and right speaker.

⁄5

BASS UP ( ) /DOWN ( ) buttons

These buttons are used to adjust the tone control of

low frequency sound for left, right and subwoofer

speaker.

⁄6

MEMO button

Memory enable button for various preset functions.

⁄7

CLEAR button

This button is used to cancel for certain memory or

programming operations.

⁄8

DISPLAY button

When this button is pressed once, the display is

dimmed.

When this button is pressed twice, the display is

turned off and the “DISPLAY OFF” indicator lights

up.

Press this button again to turn on the display

again.

⁄9

NIGHT button

Pressing this button prevents the Dolby Digital sig-

nal from playback at a loud voice. This function re-

duces the voice by 1/3 to 1/4 at maximum. Thus, it

eliminates the occurrence of an abruptly loud voice

at night. However, the function is valid only for the

case when the Dolby Digital signal is entered into

OPTICAL or COAXIAL and data to compress the

voice exists in the signal to be played back.

When this button is pressed, “NIGHT” indicator lights

up.

¤0

S- ( Source) DIRECT button

When this button is pressed, the tone control

circuit is bypassed as well as Bass Management.

¤1

SETUP / T.TONE button

Test tone function is used for adjusting the balance

between the volume levels of speaker channels.

Press AMP button and press this button to enter the

test tone mode.

¤2

OSD button

Note:

• This button is unavailable for SR4400.

¤3

SLEEP (sleep timer) button

This button is used for setting the sleep timer. It

can be operated the same way as the button in unit.

¤4

TV VOLUME UP ( ) /DOWN ( ) buttons

These buttons increase or decrease TV’s volume.

OSD

SLEEP

MUTE

AMPAUX

TUNER

TAPE

CDR/MD

DVD

POWER

VCR1

DSS/VCR2

VOL.VOL.

MAIN

PTY

ATT.

F.DIRECT

DISP./RDS

TUNE/SEARCH

MODE

TREBLE

CHANNEL/SKIP

BASS

A/D

P.SCAN

6.1CH IN

STEREO

M-CH ST

MEMO

CLEAR

DISPLAY

NIGHT

CSII EX/ES DSP

DTS

S-DIRECT

AUTO

321

654

T.TONE

MENU OFF

SETUP/

+/A

/VCR

/ANT

–/B

SR4400U DFU_01_ENG 1_2 03.4.10, 3:00 PMPage 7 Adobe PageMaker 6.5J/PPC

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz SR-4400 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info