Bedienungsanleitung Marantz SR-5001 (Seite 30 von 56) (Englisch, Holländisch)

6568

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

2-2 SPEAKERS DISTANCE

Use this parameter to specify the distance of each

speaker’s position from the listening position. The

delay time is automatically calculated according to

these distances.

Begin by determining the ideal or most commonly

used seating position in the room.

This is important for the timing of the acoustics to

create the proper sound space that the SR4001/

SR5001 and today’s sound systems are able to

produce.

Note:

For speakers that you have selected “NONE” the

Speaker Configuration sub-menu will not appear

here. (There are several useful books and special

DVD and LD’s available to guide you through proper

home theater conﬁ guration. If you are unsure, have

your Marantz dealer perform the installation for you.

They are trained professionals familiar with even

the most sophisticated custom installations. Marantz

recommends the WWW.CEDIA.ORG website for

further information about this).

2-2 SPEAKERS DISTANCE

FRONT L : 10 ft 3.0 m

FRONT R : 10 ft 3.0 m

CENTER : 10 ft 3.0 m

SURR.L : 10 ft 3.0 m

SURR.R : 10 ft 3.0 m

SUB W : 10 ft 3.0 m

SURR.B L : 10 ft 3.0 m

SURR.B R : 10 ft 3.0 m

MAIN RETURN EXIT

To select each speaker , press the 3 or 4

cursor buttons.

To set the distance for each speaker , press the

1 or 2 cursor buttons.

After you complete this portion of the set up,

move the cursor to “NEXT” with the 3 or 4

cursor buttons and then press the ENTER

button to go to the next page.

FRONT L:

Set the distance from the front left speaker to your

normal listening position.

CENTER:

Set the distance from the center speaker to your

normal listening position.

FRONT R:

Set the distance from the front right speaker to

your normal listening position.

SURR. L:

Set the distance from the surround left speaker to

your normal listening position.

SURR. R:

Set the distance from the surround right speaker

to your normal listening position.

SUB W:

Set the distance from the subwoofer to your

normal listening position.

SURR. B L:

Set the distance from the surround back left

speaker to your normal listening position.

SURR. B R:

Set the distance from the surround back right

speaker to your normal listening position.

Notes:

• Set the distance to each speaker in meters (m) or feet

(ft) as follows.

m: 0.3 - 9 m in 0.3 m steps

ft: 1 - 30 ft in 1 ft steps

• For the speakers that you have selected “NONE” the

Speaker Size menu will not appear.

• The setting for Surr.Back L and Surr.Back R appears

if you set for it to, two surround back speakers in the

Speaker Size menu.

• The setting of Surr.Back appears if it is set for one

surround back speaker in the Speaker Size menu.

2-3. SPEAKERS LEVEL SETTING WITH TEST TONE

Here you will set the volume for each speaker so that

they are all heard by the listener at the same level.

We recommend using a SPL (Sound Pressure Level)

meter, when available.

Note:

The speaker level settings are not available in 7.1

Channel Input mode, CS mode and Multi Channel

Stereo mode.

2-3 SPEAKERS LEVEL

TEST MODE : MANUAL

FRONT L : 0 dB

CENTER : 0 dB

FRONT R : 0 dB

SURR.R : 0 dB

SURR.B R : 0 dB

SURR.B L : 0 dB

SURR.L : 0 dB

SUB W : 0 dB

MAIN RETURN EXIT

TEST MODE :

Selects “MANUAL” or “AUTO” for generating

the mode of the test tone with the 1 or 2 cursor

buttons.

If you select “AUTO” , the test tone will be cycled

through in a circular pattern which is Left → Center →

Right → Surround Right → Surround Back Right →

Surround Back Left → Surround Left → Subwoofer

→ Left → .. increments of 2 seconds

for each channel.

Using the 1 or 2 cursor buttons, adjust the volume

level of the noise from the speaker so that it is the

same level for all the speakers.

If you select “MANUAL”, adjust the output level of

each speaker as listed below.

When you move the cursor to FRONT L by

pressing the 4 cursor button, the SR4001/

SR5001 will emit a pink noise from the front left

speaker.

Remember the level of this noise and then

press the 4 cursor button.

(Note that this can be adjusted to any level

between -10 and +10 dB in 1 dB intervals

except the subwoofer setting. The subwoofer

can be adjusted to any level between -15 and

+10 dB in 1 dB intervals.)

The SR4001/SR5001 will now emit the pink

noise from the center speaker.

Using the 1 and 2 cursor buttons, adjust the

volume level of the noise from the center

speaker so that it is the same level as the front

left speaker.

Press the 4 cursor button again. The SR4001/

SR5001 will now emit the pink noise from the

front right speaker.

Repeat steps

and

above for the front

right and other speakers until all speakers are

adjusted to the same volume level.

After you complete this portion of the set up, press

the ENTER button, the cursor will move to “MAIN”

and then press the ENTER button to go to SETUP

MAIN MENU.

Notes:

• Speakers that you selected “NONE” for in the

Speaker Size menu will not appear.

• The setting of Surr.Back L and Surr.Back R appears

if you have set it for two surround back speakers in

the Speaker Size menu.

•

The setting of Surr.Back appears if you have set it for

one surround back speaker in the Speaker Size menu.

• To adjust the speaker levels for 7.1-channel input

sources, you will need to use the 7.1CH-INPUT sub

menu. (See page 29).

3 PREFERENCE

STANDBY MODE : ECONOMY

TV-AUTO :

OSD INFO : ENABLE

BILINGUAL : MAIN

VIDEO CONVERT

HDMI : ENABLE

DC TRIGGER

MAIN EXIT

Select “PREFERENCE” in the SETUP MAIN

MENU with the 3 or 4 cursor buttons, and

press the ENTER button.

To select a desired content, press the 3 or 4

cursor buttons.

STANDBY MODE:

When this function is set to “ECONOMY”, you can

reduce the power consumption when the unit is in

the standby mode.

Note:

TV-AUTO and RS-232C are disabled in the

“ECONOMY” setting (SR5001 only).

TV AUTO:

Select the TV AUTO ON/OFF function to enable or

disable with the 1 or 2 cursor buttons.

OSD Info:

Select the OSD information function to enable or

disable with the 1 or 2 cursor buttons.

If you select “ENABLE”, the SR4001/SR5001 will

display the status of the feature (Volume up/down,

input select, etc..) on the TV monitor. But if you do

not desire this information, select “DISABLE”.

BILINGUAL:

In the Bilingual mode, Dolby Digital and DTS

output is set to either “MAIN” or “SUB”. Select

“BILINGUAL” with the

and

cursor buttons,

then select MAIN ↔ SUB ↔ MAIN+SUB with the

1 or 2

cursor buttons.

Marantz SR-5001 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info