Bedienungsanleitung Marantz SR-5300 (Seite 30 von 40) (Englisch)

6572

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

ENGLISH

STEREO

This mode bypasses all surround processing.

Stereo program sources the left and right channels play normally

when PCM-audio or analog stereo is input.

With Dolby Digital and DTS sources, the 5.1 multi-channels are

converted to two channel stereo. 96 kHz source material can be

playback in stereo mode.

S (SOURCE ) - DIRECT

In the source direct mode, the tone control circuit and bass

management configuration are bypassed for full range frequency

response and the purist audio reproduction.

96 kHz PCM source material can be play back in this mode.

Notes:

• Internal speaker size is setup to front L/R = Large, Center =

Large, Surround L/R = Large and Subwoofer = yes

automatically. Tone controls and additional processing are also

defeated.

• When you use this mode with certain DVD and CD players,

performing operations such as “Skip” or “Stop” may

momentarily interrupt the output.

CAUTION

NOTE for DTS signal

* Connected DVD-player, laser-disc player or CD-player needs to

support DTS-digital output. You may not be able to play some DTS

source signals from certain CD players and LD players even if you

connect the player to the SR5300 digitally. This is because the

digital signal has been processed (such as the output level,

sampling frequency, or frequency response) and the SR5300

cannot recognize the signal as DTS data.

* Depending on the player used, DTS play may produce short noise.

This is not a malfunction. In such cases, select the surround mode

the “DTS” or “DTS-ES”.

* If DTS cinema, DTS music or DTS-ES mode is selected, digital

input cannot be switched to analog input.

* When the analog input function has been selected, Surround mode

cannot be switched to DTS cinema, DTS music or DTS-ES mode.

* While signals from DTS-laser disc or CD are playing in another

Surround mode, you cannot switch to digital input or from digital input

to analog input by INPUT SETUP in SETUP MAIN MENU or A/D

button.

* The outputs for the VCR 1 OUT, DSS/VCR 2 OUT, TAPE OUT, and

CD-R OUT output analog audio signals. Do not record from CDs or

LDs that support DTS using these outputs. If you do, the DTS-

encoded signal will be recorded as noise.

NOTE for Dolby Digital Surround EX signal

* When playing Dolby Digital Surround EX-encoded software in 6.1

channels, it is required to set the EX/ES mode.

* Note that some of Dolby Digital Surround EX-encoded software

does not contain the identification signal. In this case, set the EX/

ES mode manually.

NOTE for 96kHz PCM audio

* AUTO, Source- DIRECT, and STEREO modes can be used when

playing PCM signals with a sampling frequency of 96 kHz (such as

from DVD-Video discs that contain 24 bit, 96 kHz audio). If such

signals are input during playback in one of the other surround

modes, output from SR5300 will be muted.

* Certain DVD player models inhibit digital output. For details, refer to

the player’s operation manual.

* Some DVD formatted discs featured copy protection. When using

such disc, 96 kHz PCM signal is not output from the DVD player. For

details, refer to the player's operation manual.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz SR-5300 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info