Bedienungsanleitung Marantz SR-5600 (Seite 30 von 41) (Englisch)

6578

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

ENGLISH

OTHER FUNCTION

TV AUTO ON/OFF FUNCTION

This function allows the component connected to

the TV-VIDEO in jack to control the power (ON/

OFF) to the SR5600.

AUTO POWER ON

Be sure the TV auto mode is ENABLED.

(Refer page 19 : System Setup)

Connect your TV TUNER (etc) to the TV-

VIDEO in terminal. Be sure to connect the

VIDEO input.

Turn OFF the power to the TV TUNER and the

SR5600.

Turn ON the TV TUNER and tune in a

receivable station.

When the station is received, the SR5600

turns ON and TV is selected automatically.

AUTO POWER OFF

In the above situation, turn the TV TUNER

OFF or select a channel that does not contain

any broadcast.

The power to the SR5600 switches to

STANDBY after approx. 5 minutes.

Notes:

• AUTO POWER OFF is canceled if the SR5600 is

set to a source other than TV.

The function reactivates when TV is selected again.

• Some TV broadcasts may cause the TV AUTO

FUNCTION to turn ON.

• The S-Video terminal does not support “TV

AUTO ON/OFF” function.

ATTENUATION TO ANALOG INPUT

SIGNAL

If the selected analog audio input signal is greater

than the capable level of internal processing, the

“PEAK” indicator will light up on the front display.

If this happens, you should press the ATT button

on the remote.

“ATT” indicator will be illuminated when this

function is activated. The signal-input level is

reduced by about half. Attenuation will not work

with the output signal of TAPE-OUT, CD-R/MD-

OUT, VCR1-OUT and DSS/VCR2-OUT.

This function is memorized for each individual

input source.

LISTENING THROUGH HEADPHONES

This jack may be used to listen to the SR5600’s

output through a pair of headphones. Be certain

that the headphones have a standard 1/4” stereo

phono plug. (Note that the speakers will

automatically be turned off when the headphone

jack is in use.)

Note:

• The surround mode returns to the previous setting

as soon as the plug is removed from the jack.

DOLBY HEADPHONE MODE

This feature simulates the waveforms of the actual

sounds heard from the speakers.

When headphones are used, the MENU button

automatically switches to the Dolby headphone

mode.

The OSD that appears when the MENU button is

pressed is shown below.

DOLDBY HP (Headphone) MODE can be selected

with the left and right cursor buttons.

BYPASS → DH1 → DH2 → DH3 → BYPASS

BYPASS: Bypasses the Dolby headphone mode

and delivers ordinary 2-channel stereo.

DH1: The size of a typical living room space

is simulated.

DH2: The expansiveness of a structure as

large as a music hall is simulated.

DH3: A large space such as that found in a

movie theater is simulated.

When the PURE DIRECT mode is selected, Dolby

surround processing is bypassed and “✽✽✽” is

displayed as the mode indication.

The surround mode can be selected when any of

the modes in DH1, DH2, or DH3 is selected.

L/R LEVEL can be set in the ±10 dB range.

Notes:

• The surround mode returns to the previous setting

as soon as the plug is removed from the jack.

• TONE cannot be set when any of the modes in

DH1, DH2, or DH3 is selected.

• The Dolby Headphone function will not work

when 32 or 96 kHz PCM digital signals are input.

VIDEO ON/OFF

When no video signal is connected to the SR5600

or a DVD, etc., is connected directly to your TV, the

unnecessary video circuit can be turned off by

selecting the “VIDEO OFF” setting.

To select video off, press the AMP button and

press the V-OFF button.

DISPLAY MODE

You can select the display mode for the front

display of the SR5600.

To select this mode, press the DISPLAY on the

remote control.

When this button is pressed, the display mode is

switched in the following sequence.

→ Surround Mode → Auto-display Off → Display

Off → Input Function → Surround Mode....

In Auto display off mode, the display is off. But, if

you make a change to the unit such as input or

surround mode, the display will show that change,

then go back to off after about 3 seconds. When

changing the volume, it is not displayed.

In Display off mode, the display is off completely.

Note:

• Only the DISP indicator will be illuminated on the

front display in display off condition

CH.SEL LIP.SYNC

PTY

SUB-T/ATT

AUDIO

INPUT/DISC+

F.DIRECT

RDS

T-MODE

SYSTEM REMOTE CONTROLLER

RC5500SR

SURROUND

AV SURROUND RECEIVER SR5600

INPUT SELECTOR

POWER ON / STANDBY PHONES

STANDBY

MULTI

M. SPEAKER B

PURE

SETUP

DIRECT

SIMPLE

AUTO

HT-EQ

MODE

DISP MULTI AUT O TUNED ST V

–

SLEEP

SURR

AUTO

DIRECT DISC 6.1

HEAD PHONE

DOLBY HP MODE : BYPASS

SURROUND :

✽✽✽

L LEVEL : 0dB

R LEVEL : 0dB

OSD

VOL.

MAIN

SLEEP

MUTE

AMP

TUNER

TAPE

CDR/MD

AUX1

TUNE/SEARCH

TREBLE

CHANNEL/SKIP

BASS

A/D

P.SCAN/V-OFF

7.1CH IN

STEREO

MCH-ST

MEMO

CLEAR

DISPLAY

NIGHT

CSII EX/ES VIRTUAL

654

SURROUND

R5600

PURE

SETUP

DIRECT

SIMPLE

AUTO

HT-EQ

ENTER

DISPLAY

MEMORY

CLEAR

T-MODE

EXIT

BAND

MODE

DISP MULTI AUT O TUNED ST V

–

OFF NIGHT PEAK ANALOG

DIGITAL

ATT

SLEEP

SURR

AUTO

DIRECT DISC 6.1 MT X 6.1 EQ

DIGITAL

SURROUND

AAC

PCM

SL S SR

LFE

F.DIRECT

RDS

TUNE/SEARCH

T-MODE

TREBLE

CHANNEL/SKIP

BASS

A/D

P.SCAN/V-OFF

7.1CH IN

STEREO

MCH-ST

MEMO

CLEAR

DISPLAY

NIGHT

CSII EX/ES VIRTUAL

DTS

PURE DIRECT

AUTO

321

654

T.TONE

MENU OFF

SET UP/

SURROUND

SR5500

PURE

SETUP

DIRECT

SIMPLE

AUTO

HT-EQ

ENTER

DISPLAY

MEMORY

CLEAR

T-MODE

EXIT

BAND

MODE

DISP MULTI AUT O TUNED ST V

–

OFF NIGHT PEAK ANALOG

DIGITAL

ATT

SLEEP

SURR

AUTO

DIRECT DISC 6.1 MT X 6.1 EQ

DIGITAL

SURROUND

AAC

PCM

SL S SR

LFE

SR5600U DFU_01_ENG 2_2 05.6.3, 3:43 PMPage 27 Adobe PageMaker 6.5J/PPC

Marantz SR-5600 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info