Bedienungsanleitung Marantz SR-8300 (Seite 37 von 57) (Englisch)

6604

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

ENGLISH

BASS PEAK LEVEL

With Dolby Digital and DTS , not only the LFE (Low Frequency

Effects), but also the bass of all channels can be heard from the

Subwoofer or Large-speakers. This procedure prevents these

speakers from becoming too loud and creating an unbalanced sound.

Since the sound is output at a loud volume, perform this operation

carefully.

Note:

• If your system does not include a subwoofer, this setting will set

the bass peak level for your front speakers.

TEST SIGNAL: Press the OK or Left button, START is indicated and

it begins to generate a Bass test tone from the

speaker which was designated “bass signal output”

during setup.

There will be no audible sound yet because the

Master volume is set to minimum automatically.

Press Down cursor button to move the cursor to

VOLUME control.

VOLUME: Adjust the bass test tone output level up until the

bass begins to distort or you reach the maximum

level with the VOL+, VOL– or Right / Left cursor

button.

Press Down cursor button to move the cursor to

ENTER.

ENTER: Press the OK button, ENTER will blink and stop

generating the Bass Peak test tone.

The Bass Peak Limit Level for your system has now

been memorized.

If you finish these setup, move cursor to “MAIN” with Up or Down

cursor button and then press OK button to go to MAIN menu.

Notes:

• Each time the subwoofer level is changed, perform the Bass

Peak Level setup and correct the setting.

• The bass peak level is not available in SOURCE-DIRECT and

7.1CH-INPUT mode.

• The selected value is displayed in the volume column before the

test signal starts.

2 - 4 BASS PEAK LEVEL

BASS PEAK TEST : START

VOLUME LEVEL : +1 8 dB

--------------------

ENTER

MA I N RETURN EX I T

PREFERENCE

Select “PREFERENCE” in MAIN SETUP MENU with Up or Down

cursor button, and press the OK button.

To select a desired content, press Up or Down cursor button.

TV AUTO: Select the TV AUTO ON/OFF function to enable or

disable with Left or Right cursor button.

(refer to page 43)

OSD Info: Select the OSD information function to enable or

disable with Left or Right cursor button.

If you select “ENABLE”, SR8300 will display the status

of the feature (Volume up/down, input select, etc..) on

the TV monitor. But if you do not desire this

information, select “DISABLE “.

DIG. OUT: Select the digital source to output the DIGITAL OUT

terminals with Left or Right cursor button.

This is for digital dubbing to a CD-R recorder or MD

deck. (See page 44)

The source is switched in the following sequence.

SOURCE →DIG.1 →DIG.2 →→→DIG.5 →DIG.6 →

AUX →OFF →SOURCE →

SUB-W OUT: “THX” position is required, but If you desire an

additional front L/R mixed subwoofer output in the

STEREO mode, select “L/R MIX” with Left or Right

button.

If you finish the setup in this item, move cursor to “MAIN” with Up or

Down cursor buttons and press OK button.

3 PREFERENCE

TV-AUTO : DISABLE

OSD I NFO : ENABLE

DIGITAL OUT : SOURCE

SUBWOOFER OUT : THX

MA I N EX I T

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz SR-8300 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantz SR-8300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info