10
ENGLISH
REMOTE CONTROL RANGE
The distance between the transmitter of the
remote control and the IR SENSOR of the SR7500
should be less than 5 meters. If the remote control
is pointed in a direction other than the IR SENSOR
or if there is an obstacle between them, use of the
remote control may not be possible.
Remote-controllable range
LOADING BATTERIES
The life of the batteries used with the remote control
is about 4 months with normal use. Also be sure to
replace batteries earlier when you notice that they
are getting weak.
1.
Remove the back cover.
2.
Insert the new batteries (AAA type) with
correct and polarity.
3.
Close the cover until it clicks.
CAUTIONS ON BATTERIES
• Use “AAA” type batteries in this remote control
unit.
• If the remote control unit does not operate from
close to the main unit, replace the batteries with
new ones, even if less then a year has passed.
• The included battery is only for verifying
operation. Replace it with a new battery as soon
as possible.
• When inserting the batteries, be careful to do so
in the proper direction, following the + and -
marks in the remote control unit’s battery
compartment.
• To prevent damage or battery fluid leakage:
- Do not use a new battery with an old one.
- Do not use two different types of batteries.
- Do not short-circuit, disassemble, heat or
dispose of batteries in flames.
• Remove the batteries when not planning to use
the remote control unit for a long period of time.
• If the batteries should leak, carefully wipe off the
fluid from the inside of the battery compartment,
then insert new batteries.
• When disposing of used batteries, please
comply with governmental regulations or
environmental public instruction’s rules that
apply in your country or area.
Remote control unit (RC8500SR)
SR7500
BATTERY REPLACEMENT INTERVAL
Under normal usage, alkaline batteries last
approximately four months. When the batteries
wear out, a battery mark is displayed on the LCD.
Although the remote control can still be used when
the battery mark is displayed, the batteries should
be replaced as soon as possible. The LCD
eventually starts to flash when buttons are
pressed, the remote control will be unable to
transmit signals or learn codes.
• This remote control uses non-volatile memory
so that the learned codes and macro programs
are retained even if the batteries are removed.
Reset the clock after replacing the batteries.
Safety Precautions for Batteries
Be sure to always observe the following
precautions to prevent fluid leakage, overheating,
fire, breakage, accidental ingestion, and other
accidents.
• If the batteries are left unused for a long period
of time, the battery fluid may leak or the batteries
may corrode.
• Do not use the batteries in the remote control
with the plus and minus polarity reversed.
•
Do not attempt to recharge, heat, or disassemble
the batteries. Do not put the batteries in a fire.
• Do not use the remote control with old batteries
or worn-out batteries inserted.
• Do not use different types of batteries or mix old
and new batteries in the remote control.
• If the remote control is not operating properly,
replace the batteries with new ones.
• If any of the batteries are leaking, completely
wipe up all leaked battery fluid, and then replace
the batteries with new ones.
SETTING THE TIME
Example: Setting to 6:20PM (18:20)
When you bought this remote control and insert
the batteries to the remote control at first, the steps
1 to 3 are skipped.
Starts from step 4 to set the time.
1.
Hold down the M button for three seconds or
more.
The menu is displayed.
2.
Press the > button once.
This displays second page (SETUP).
3.
Press the D4 (CLOCK) direct button.
The “ ” indicator blinks and the clock indicator
displays “0:00”.
4.
Press the 1 and 8 numeric button to set the
hour indicator.
The hour indicator displays “18”.
The minute indicator blinks “_”.
5.
Press the 2 and 0 numeric button to set the
minute indicator.
The minute indicator displays “20”.
The hour indicator blinks.
6.
Press the OK cursor button to start the clock.
The clock starts from 0 second at the time that was
set and return to normal (USE) mode.
Whenever the batteries are replaced, the clock
shows 00:00. Please reset the clock. (The time
setting is not backed up.)
