Bedienungsanleitung Marantz SR4001 (Seite 13 von 56) (Englisch, Holländisch)

522884

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

‹2 AUDIO buttons

(When DVD mode is selected)

Used to select one of the audio language.

‹3 TREBLE +/- buttons

These buttons are used to adjust the tone control of

high frequency sound for left and right speaker.

‹4 SOURCE button

These buttons are used to switch the source of your

A/V Receiver / amplifer. Each time a source button is

pressed, the remote control changes to the source

which was pressed.

This remote control can control 12 types of equipment.

To change the A/V Receiver / ampliﬁ er source, press

this button twice within two seconds. The signal is

sent when it is pressed the second time.

Note:

Select the AMP as the source to use this remote

controll with the SR4001/SR5001.

‹5 Infrared Transmitter and Learning

Sensor

This transmitter emits infrared light. Press the buttons

while pointing the transmitter towards the infrared

receiver window of the SR4001/SR5001 or other

AV equipment. Be sure to also point towards other

remote controls when using the learning function.

¤6 VOLUME +/- buttons

This button is used to adjust the volume for the

ampliﬁ er and television.

Note:

Set the AMP mode to use this button with the SR4001/

SR5001.

¤7 M-SPKR button

(SR5001 only)

(When AMP mode is selected)

Used to turn on and off multi speaker.

¤8 MENU button

(When AMP mode is selected)

This button is used to call up the SETUP MAIN

MENU of the SR4001/SR5001.

¤9 1,

(CURSOR) / ENTER buttons

These buttons are used when controlling the cursor of

the SR4001/SR5001, DVD or other AV equipment.

‹0 EXIT button

(When AMP mode is selected)

This button is used to cancel setting in the setup

menu.

‹1 SUBTITLE/ATT. button

(When AMP mode is selected)

When the input signal is too high and the voice

distorts even by throttling the SR4001/SR5001

VOLUME control, turn on this function.

“ATT” is indicated when this function is activated.

The input level reduced. Attenuator is invalid for the

output signal of “REC OUT”.

Note:

This function is unavailable while the digital input is

selected.

¤1 BAND/LIP SYNC/INPUT button

(When TUNER mode is selected)

Used to select a radio band.

(When AMP mode is selected)

Used to select LIP SYNC mode.

(When TV mode is selected)

Used to select monitor input.

¤2 T.MODE button

(When TUNER mode is selected)

Used to select auto stereo mode or mono mode

when the FM band is selected.

The “AUTO” indicator lights in the auto stereo mode.

¤3 P.SCAN button

(When TUNER mode is selected)

Used to start preset scan.

¤4 MEMO/HT-EQ button

This button is used to store setting to memory or

program a source.

(When AMP mode is selected)

Used to turn on or off HT(Home Theater)-EQ mode

when the surround mode is set as AUTO, DOLBY,

DTS or STEREO.

This mode compensates for the audio portion of a

movie sounding “bright”.

When this button is pressed, “EQ” indicator light up.

¤5 MUTE button

This button is used to mute the audio for the ampliﬁ er

and television.

Note:

Set the AMP mode to use this button with the SR4001/

SR5001.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz SR4001 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info