Bedienungsanleitung Marantz SR4001 (Seite 31 von 56) (Englisch, Holländisch)

522884

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

6 CS

(CIRCLE SURROUND

) PARAMETER

6 CS II PARAMETER

TRUBASS : 0

SRS DIALOG : 0

MAIN EXIT

Select “CS

” in the SETUP MAIN MENU

with the 3 or 4 cursor buttons, and press the

ENTER button.

To Select desired contents as below, press the

3 or 4 cursor buttons.

TRUBASS:

Set the TRUBASS level between 0 and 6 level in 1

level interval with the 1 or 2 cursor buttons.

TRUBASS produced by the speakers are an octave

below the actual physical capabilities of the speakers

adding exciting, deeper bass effects.

SRS DIALOG:

Set the SRS DIALOG level between 0 and 6 in 1

level intervals with the 1 or 2 cursor buttons.

This can be popped out of the surround audio

effects, allowing the listener to easily discern what

the actors say.

If “NONE” was selected for the Center speaker

setting, in the Speaker size set up menu, then this

setting will not appear.

After you complete this portion of the set up, move

cursor to “MAIN” with the 3 or 4 cursor buttons and

press the

ENTER

button.

VIDEO CONVERT:

Select the VIDEO CONVERT function to enable

or disable with the 1 or 2 cursor buttons. (Video

cable connection: Refer to page 19)

3-1 VIDEO CONVERT

TV : ON

DVD : ON

VCR1 : ON

DSS : ON

AUX1 : ON

MAIN RETURN EXIT

After you complete this portion of the set up, move

the cursor to “MAIN” with the 3 or 4 cursor buttons

and press the

ENTER

button.

HDMI AUDIO:

This setting determines whether to playback audio

input to the HDMI jacks through the SR4001/

SR5001 or output it through the receiver to a TV

or projector.

ENABLE: The audio input to the HDMI jacks

can be played back by this receiver.

In such case, audio signals are not

output to the TV or projector.

THROUGH: The audio input to the HDMI jacks is

not output from the speaker terminals

of the SR4001/SR5001. Audio data is

output directly to the TV or projector.

This setting is used to listen to audio

on a multi channel TV, etc.

DC TRIGGER:

Select “DC TRIG SETUP” in the SETUP MAIN

MENU with 3 or 4 cursor button, and press the

ENTER button.

3-2 DC TIRGGER SETUP

DC TRIG DISABLE

TV : CD :

DVD : TAPE :

VCR1 : CD-R :

DSS : AUX2 :

AUX1 : TUNER:

7.1CH:

MAIN RETURN EXIT

You can select MAIN ROOM, MULTI ROOM,

REMOTE or DISABLE by pressing 1 or 2 cursor

buttons.

Notes:

• REMOTE is available for the external control. The

RC5001SR cannot operate this function.

• To select desired input source , press 3 or 4 cursor

button.

• To set ON or OFF, press 1 or 2 cursor button.

• After you complete this portion of the set up, move

the cursor to “MAIN” with the 3 or 4 cursor

buttons and press the ENTER button.

4 SURROUND

SURR.MODE :AUTO

HT-EQ :OFF

LFE LEVEL :

MAIN EXIT

Select “SURROUND” in the SETUP MAIN

MENU with the 3 or 4 cursor buttons, and

press the ENTER button.

To select a desired content , press the 3 or 4

cursor buttons.

SURR.MODE:

Select the desired surround mode with the 1 or 2

cursor buttons.

HT-EQ:

Select to active the HT-EQ with the

1 or 2

cursor

buttons.

The tonal balance of a film soundtrack will be

excessively bright and harsh when played back

over audio equipment in the home. This is because

ﬁ lm soundtracks were designed to be played back

in large movie theater environments.

Activating the HT-EQ feature when watching a ﬁ lm

made for movie theaters corrects this and restores

the correct tonal balance.

The HT-EQ feature is available except in the

following modes.

• 7.1 CH INPUT

• PURE-DIRECT

• When VIRTUAL is set for the surround mode

LFE LEVEL:

Select the output level of the LFE signal included in

the Dolby Digital signal or the DTS signal.

Select 0 dB, -10 dB or OFF with the 1 or 2 cursor

buttons.

After you complete this portion of the set up, move

the cursor to “MAIN” with the 3 or 4 cursor buttons

and press the ENTER button.

5 PL

(PRO LOGIC

)

MUSIC PARAMETER

Pro Logic II-Music mode creates a rich and enveloping

surround ambience from stereo sources such as

CDs.

In this mode, SR4001/SR5001 includes three controls

to ﬁ ne-tune the soundﬁ eld as follows.

5 PL II MUSIC PARAMETER

PARAMETER : DEFAULT

PANORAMAA : OFF

DIMENSION : 3

CENTER WIDTH : 3

MAIN EXIT

Select “PL

MUSIC” in the SETUP MAIN MENU

with the 3 or 4 cursor buttons, and press the ENTER

button.

PARAMETER:

Select “DEFAULT” or “CUSTOM” with the 1 or 2

cursor buttons.

If you select “CUSTOM”, you can adjust three

parameters as listed below.

PANORAMA:

Select the Panorama mode On or Off with the

1 or 2 cursor buttons.

Panorama wraps the sound of the front left and right

speakers around you, for an exciting perspective.

DIMENSION:

Set the Dimension level between +3 and –3 level

in 1 level intervals with the 1 or 2 cursor buttons.

Adjust the soundﬁ eld either towards the front or

towards the rear.

This can be useful to help achieve a more

suitable balance from all the speakers with certain

recordings.

CENTER WIDTH:

Set the Center width level between 0 and 7 in 1

level intervals with the 1 or 2 cursor buttons.

Center Width allows you to gradually spread the

center channel sound into the front left and right

speakers.

At its widest setting, all the sound from the center

is mixed into the left and right.

This control may help achieve a more spacious

sound or a better blend for the front image.

If “NONE” was selected for the Center speaker

setting, in the Speaker size set up menu, then this

setting will not appear.

After you complete this portion of the set up, move

cursor to “MAIN” with the 3 or 4 cursor buttons and

press the ENTER button.

Marantz SR4001 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info