Bedienungsanleitung Marantz SR4001 (Seite 37 von 56) (Englisch, Holländisch)

522884

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

ENGLISH

CSII -Mono mode

This mode plays back monaural recordings from

any source, including CDs, DVDs and TV and radio

broadcasts in compelling 6.1-channel surround.

Notes:

• CS II mode is available for 2ch input signals which

are encoded in Dolby Digital or PCM format.

• PCM-audio signals can be subjected to Pro Logic

processing when the sampling frequency is 32 kHz,

44.1 kHz or 48 kHz.

VIRTUAL

This mode creates a virtualized surround sound

experience from a two-speaker (front L and R)

playback system playing any multichannel audio

source (such as found on DVDs and digital

broadcasts), including Dolby Digital, Dolby Pro Logic

or DTS.

STEREO

This mode bypasses all surround processing.

In stereo program sources, the left and right channels

play normally when PCM-audio or analog stereo is

input.

With Dolby Digital and DTS sources, the 5.1

multichannels are converted to two channel stereo.

96 kHz PCM source material can be played back in

stereo mode.

SOURCE DIRECT

In the Source Direct mode, the tone control circuit

and bass management conﬁ guration are bypassed

for full-range frequency response and the purist

audio reproduction.

Notes:

• Speaker size is set to Front L/R = LARGE, Center =

LARGE, Surround L/R = LARGE and Subwoofer

= YES automatically. Tone controls, equalizer and

additional processing are deactivated.

• When you use this mode with certain DVD and CD

players, performing operations such as skip or stop

may momentarily interrupt the output.

PURE DIRECT

The Pure Direct mode further reduces sources of

noise in addition to effect of the Source Direct mode,

by blocking output from the video jacks (VIDEO,

S-VIDEO, COMPONENT VIDEO and HDMI) and

turning the FL display off.

CAUTION

NOTE for DTS signal

* Connected DVD-player, laser-disc player or

CD-player needs to support DTS-digital output.

You may not be able to play some DTS source

signals from certain CD players and LD players

even if you connect the player to the SR4001/

SR5001 digitally. This is because the digital signal

has been processed (such as the output level,

sampling frequency, or frequency response) and

the SR4001/SR5001 cannot recognize the signal

as DTS data.

* Depending on the player used, DTS play may

produce a short noise. This is not a malfunction.

* While signals from DTS-laser disc or CD are

playing in another Surround mode, you cannot

switch to digital input or from digital input to analog

input by INPUT SETUP in SETUP MAIN MENU or

the A/D button.

* The outputs for the VCR 1 OUT, DSS/VCR 2

OUT, TAPE OUT, and CD-R OUT output analog

audio signals. Do not record from CDs or LDs that

support DTS using these outputs. If you do, the

DTS-encoded signal will be recorded as noise.

NOTE for Dolby Digital Surround EX signal

* When playing Dolby Digital Surround EX-encoded

software in 6.1 channels, it is required to set the

EX/ES mode.

* Note that some of Dolby Digital Surround

EX-encoded software does not contain the

identiﬁ cation signal. In this case, set the EX/ES

mode manually.

NOTE for 96kHz PCM audio

* AUTO, PURE-DIRECT, and STEREO modes

can be used when playing PCM signals with a

sampling frequency of 96 kHz (such as from DVD-

Video discs that contain 24 bit, 96 kHz audio). If

such signals are input during playback in one of

the other surround modes, output from SR4001/

SR5001 will be muted.

* Certain DVD player models inhibit digital output.

For details, refer to the player’s operation manual.

* Some DVD formatted discs feature copy protection.

When using such disc, 96 kHz PCM signal is not

output from the DVD player. For details, refer to

the player’s operation manual.

NOTE for HDCD signal

* HDCD is effective only at the time of digital input.

* AUTO, PURE DIRECT, and STEREO modes can

be used when playing HDCD signals (such as

from CD discs that contain HDCD).

* You may not be able to play some HDCD source

signals from certain CD players if you connect

the player to the SR4001/SR5001 digitally. This

is because the digital signal has been processed

(such as the output level, sampling frequency, or

frequency response) and the SR4001/SR5001

cannot recognize the signal as HDCD data.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz SR4001 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info