Bedienungsanleitung Marantz SR4003 (Seite 37 von 48) (Englisch)

61338

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

ENGLISH

BASIC

CONNECTIONS

BASIC OPERATION

ADVANCED

CONNECTIONS

SETUP

ADVANCED

OPERATION

TROUBLESHOOTING

OTHERS

NAMES AND

FUNCTIONS

ADVANCED

OPERATION

RESETTING THE CODE

Press and hold down the SOURCE button

for appliance which should be controlled and

press SET button until the SEND indicator

blinking twice.

Then back light ﬂ ushes.

Press the below codes to reset.

TV : 1000

DVD : 2000

CD : 3000

DSS : 4000

The indicator will blink twice.

Note:

After this procedure, the selected SOURCE button is

set initial code.

Press and hold down the SOURCE button for

appliance which should be controlled and press

SET button until the SEND indicator blinking

twice. Then back light ﬂ ushes.

Aim the remote control at the appliance and

slowly alternate between pressing INPUT 3

button and the

SOURCE ON/OFF

button for the

appliance.

Stop when the appliance turns off.

Press ENTER button once to lock in the code.

CHECKING THE CODE

Press and hold down the SOURCE button for

appliance which should be controlled and press

SET button until the SEND indicator blinking twice

then back light ﬂ ushes.

Press the INFO button.

The SEND indicator will blink twice.

To view the code for ﬁ rst digit, press 1 once.

Wait 3 seconds, count the SEND indicator

blinks (e.g. 3 blinks = 3) and write down the

number.

Note:

If a code digit is “0”, the SEND indicator will not

blink.

Repeat step

three more times for remaining

digits. Use 2 for the second digit, 3 for the third

digit, and 4 for the fourth digit.

Importants:

• Some codes may be not match your equipment.

In this case, you can use LEARN mode to store these

codes.

• The preset codes do not cover full functions.

If you need extra function, use LEARN mode to

store extra function.

• Wen the batteries are getting weak, the preset

procedure is not successful.

PROGRAMMING WITH THE 4-DIGIT CODE

Press and hold down the SOURCE button for the

appliance which should be controlled and press

SET button until the SEND indicator blinks twice.

Then back light ﬂ ushes.

2. Press the 4-digit code by numeric buttons for

appliance (code table at the end of this book)

When the procedure is successful, the

SEND

indicator will blink twice.

Note:

If the indicator did not blink twice, then repeat steps 1

through 2 and try entering the same code again.

SCANNING THE CODE TABLE

Switch on the appliance which should be

controlled.

BASIC OPERATION (REMOTE CONTROLLER)

NORMAL MODE

(

When operating Marantz AV equipment products

)

This remote controller is preset with a total of 12 types

of remote codes, including Marantz TV (television),

DVD, VCR (VCR deck), DSS (satellite broadcasting

tuner), TUNER, CD, CD-R, DMP, TAPE (tape deck),

AUX1, AUX2, and AMP (ampliﬁ er).

Learning is not necessary for Marantz products. You

can use these products without setting any codes.

1. Press the SOURCE button.

For this example, press DVD.

Pressing the SOURCE button once changes

the remote control to the settings for the source

that was pressed.

To change the ampliﬁ er on other source, press

the SOURCE button twice (double-click). The

code is sent, and then the ampliﬁ er source

changes to DVD.

SETTING THE BACK LIGHT

Pressing the Light button located on the side of

the remote controller lights the remote controller’s

backlight. Pressing the button again while the backlight

is lit lights the backlight for another 2 seconds.

To turn off back light, press and hold down the SET

and OFF button until SEND indicator blinks twice.

To turn on it again, press and hold down the SET and

ON button until SEND indicator blinks twice.

Initial is back light ON.

PRESET MODE

(When operating non-Marantz AV equipment

products)

This remote controller is preset with remote control

codes from AV equipment by other manufacturers.

The preset codes are TV, CD, DVD and DSS.

Settings can be made in one of two ways.

When the preset codes are set, the following codes

are contained in the source button of the remote

controller.

See the attached manufacturer number list for the

preset manufacturers, devices, preset numbers, and

other settings.

Remote controller

source name

Corresponding preset

code

Device name

TV TV Television

DVD DVD DVD player

CD CD CD player

DSS SATELLITE Satellite broadcasting

tuner equipment

SR4003_U_01_E2_2.indd 34SR4003_U_01_E2_2.indd 34 08.6.20 5:06:32 PM08.6.20 5:06:32 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz SR4003 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantz SR4003

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info