Bedienungsanleitung Marantz SR5004 (Seite 53 von 96) (Englisch)

522801

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

NAMES AND

FUNCTIONS

BASIC

CONNECTIONS

BASIC

OPERATION

ADVANCED

CONNECTIONS

SETUP

ADVANCED

OPERATION

TROUBLESHOOTING

OTHERS

ADVANCED

OPERATION

ENGLISH

ADVANCED OPERATION

PRESET SCAN

1. Press the TUNE button twice within two

seconds on the remote controller.

2. Press the BAND button to select XM band.

3. Press the P.SCAN button on the remote

controller.

4. Preset channels are recalled in sequence

(No.1 → No.2 → etc.) for about 10 seconds

each. The time changes by the received

condition. No stored preset number will be

skipped.

5. Pressing the 2 button during prescanning

speeds up scanning.

Also, pressing the 1 button returns to the

previous preset channel.

6. When the desired preset channel is

received, cancel the preset scan operation

by press the P. SCAN button.

CLEARING STORED PRESET CHANNELS

You can remove preset channels from the memory

using the following procedure.

2. 3.

1. Recall the preset number to be cleared with

the method described in “PRESET SEARCH

MODE”.

2. Press the MEMORY button on the front

panel or press the MEMO button on the

remote controller.

3. The stored preset number blinks in the

display for 5 seconds. WhiIe blinking, press

the CLEAR button on the front panel or CLR

button on the remote controller.

4. “xx CLEAR” appears on the dispIay to

indicate that the speciﬁ ed preset number

has been cleared.

Notes

• To clear all stored preset channel, press and hold

the T.MODE and the ENTER buttons on the unit

for two seconds.

• There are 50 preset channels prepared at the

factory default. The 50 channels are all set to

“CHANNEL 001”. Each channel can be stored

in the preset memory. You can search for only the

preset channels.

LISTENING TO

SIRIUS SATELLITE RADIO

SELECTING AN INPUT SOURCE

Before you can listen to SIRIUS Satellite Radio, you

must ﬁ rst select the input source on the unit.

1. 2.

(Using the unit)

1. Turn the INPUT SELECTOR knob to select

“TUNER”.

2. Press the BAND button to select SIRIUS.

(Using the remote controller)

1. To select tuner, press the TUNE button

twice within two seconds on the remote

controller.

2. Press the BAND button to select SIRIUS.

CHECKING THE SIRIUS SIGNAL

STRENGTH AND RADIO ID

1. Press the TUNE button on the remote

controller.

2. Press the T.DISP button 3 times to display

the signal status on the front display of the

unit.

SR SAT :

SR TERR:

• The top line of the display shows the strength

of the signal received from satellite, while the

bottom line displays the strength of the terrestrial

signal received.

• An mark indicates the strength of the stronger

of the satellite and terrestrial signals.

• The display changes as shown below according

to the receiving condition.

EXCELENT display

SR :

GOOD display

SR :

WEAK display

SR :

NO SIGNAL display

SR :

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz SR5004 Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info