Bedienungsanleitung Marantz SR5006 (Seite 138 von 146) (Englisch)

522825

138

Zoom out

Zoom in

Vorherige Seite

1/146

Nächste Seite

135

GAudioH

Symptom Cause/Solution Page

Audio is not output. •Check the connections for all devices.

•Check the speaker connections and conﬁgurations.

•Check whether the audio device power is turned on.

•Adjust the master volume.

•Cancel the mute mode.

•Select a suitable input source.

•Select a suitable input mode.

•Disconnect the headphones. No sound is output from the

speakers when headphones are connected.

C3,8,

10,11,12,13,

14,15,16,

17,18

C6,58,

59,60,61,

62,63

–

27, 79

26, 79

109

120

No sound is

produced from

surround speaker.

•Check if the surround speakers are connected to the SURROUND

terminals.

–

No sound is

produced from

surround back

speaker.

•Check if “Amp Assign” is set appropriately in order to output

audio from the surround back speakers.

•Set “Speaker Conﬁg.” – “S.Back” on the menu to something

other than “None”.

•Set the surround mode to something other than “STEREO” and

“VIRTUAL“.

No sound is

produced from front

height speaker.

•Check if “Amp Assign” is set appropriately in order to output

audio from the front height speakers.

•Set “Speaker Conﬁg.” – “F.Height” on the menu to something

other than “None”.

No sound is

produced from

subwoofer.

•Check the subwoofer connections.

•Turn on the subwoofer’s power.

•Set “Speaker Conﬁg.” – “Subwoofer” on the menu to “Yes”.

•If “Front” and “Center” for “Speaker Conﬁg.” are set to “Large”,

and “Subwoofer Mode” is set to “LFE”, no sound may be output

from the subwoofers, depending on the input signal or selected

surround mode.

C6,58,

59,60,61,

62,63

–

92, 93

DTS sound is not

output.

•Set “Decode Mode” on the menu to “Auto” or “DTS”.

109

Symptom Cause/Solution Page

Dolby TrueHD, DTS-

HD, Dolby Digital

Plus audio is not

output.

•Make HDMI connections.

Dolby PLg mode or

DTS NEO:6 mode

cannot be selected.

•Check that “Speaker Conﬁg.” – “Center” or “Surround” is set

to other than “None”. If the speaker system is 2.0/2.1ch, this

surround mode cannot be selected.

•When headphones are used, Dolby PLg or DTS NEO:6 cannot be

selected.

–

Audyssey MultEQ

XT, Audyssey

Dynamic EQ

and

Audyssey Dynamic

Volume

cannot be

selected.

•Switch the surround mode to other than “DIRECT” or “PURE

DIRECT”.

•When headphones are used, MultEQ

XT, Dynamic EQ

and

Dynamic Volume

cannot be selected.

–

Dynamic EQ

and

Dynamic Volume

cannot be selected.

•Run Audyssey

Auto Setup.

19, 64

M-DAX cannot be

selected.

•Check that an analog signal or PCM signal (fs=44.1/48 kHz) is

input. For playback of multichannel signals such as Dolby Digital

or DTS surround, M-DAX cannot be used.

•Switch the surround mode to other than “DIRECT” or “PURE

DIRECT”.

GRadioH

Symptom Cause/Solution Page

Reception fails, or

there is a lot of noise

or distortion.

•Change the antenna orientation or position.

•Separate the AM loop antenna from the unit.

•Use an FM outdoor antenna.

•Separate the antenna from other connection cables.

Basic version

Advanced version

InformationInformation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz SR5006 Seite 138

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantz SR5006

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info