Bedienungsanleitung Marantz SR6003 (Seite 47 von 90) (Englisch)

61897

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

ENGLISH

BASIC

CONNECTIONS

BASIC OPERATION

ADVANCED

CONNECTIONS

SETUP

ADVANCED

OPERATION

TROUBLESHOOTING

OTHERS

NAMES AND

FUNCTION

ADVANCED

OPERATION

M-DAX (Marantz Dynamic Audio eXpander)

This function makes up for lost audio content in MP3

or AAC sources (from lossy compression) during

playback. Choose one of the following levels for this

effect as desired.

“HIGH”: Stronger effect

“LOW”: Weaker effect

“OFF”: Deactivated.

(Using the remote controller)

When switching to M-DAX mode, press the AMP

button.

Press the M-DAX button.

Each time this button is pressed, M-DAX changes

as follows.

OFF LOW HIG

The “M-DAX” indicator on the front display lights

when M-DAX mode is LOW or HIGH. (See page 6)

Notes:

• M-DAX is compatible with PCM (48 kHz or lower)

and two-channel analog sources.

• The M-DAX is not available when Dolby Virtual

Speaker mode is being used.

ATTENUATION TO ANALOG INPUT SIGNAL

If the selected analog audio input signal is greater

than the capable level of internal processing, the

“PEAK” indicator will light up on the front display. If

this happens, you should press the ATT button on

the remote controller.

“ATT” indicator will be illuminated when this function

is activated. The signal-input level is reduced by

about half. Attenuation will not work with the output

signal of TAPE-OUT, CD/CD-R and VCR-OUT.

This function is memorized for each individual input

source.

SPEAKER A/B

This unit has speaker system-A and speaker system-

B for front L/R channels.

You can select these systems by pressing SPKR A/B

on the remote controller.

Press the SPKR A/B button.

Each time this button is pressed, Speaker system A

and B changes as follows.

A B A+B OFF

7.1 CH INPUT

This unit is equipped for future expansion through the

use of Multi channel Super Audio CD multichannel

player or DVD-Audio player.

When this is selected, the input signals connected to

the L(front left), R (front right), CENTER, SL (surround

left), SR (surround right) and SBL (surround back left)

and SBR (surround back right) channels of the 7.1

CH. In jacks are output directly to the front (left and

right), center, surround (left and right) and surround

back speaker systems as well as the pre-out jacks

without passing through the surround circuitry.

In addition, the signal input to the SW (subwoofer)

jack is output to the PRE OUT SW (subwoofer) jack.

When 7.1 CH. INPUT is selected, the last video input

used remains routed to the Monitor Outputs.

This permits simultaneous viewing with video

sources

Select a desired Video source to decide the

routed video signal to the Monitor Outputs.

Press the 7.1 button on the remote controller to

switch the 7.1 channel input.

If it is necessary to adjust the output level of

each channel, press the CH.SEL button on the

remote controller.

Adjust the speaker output levels so that you can

hear the same sound level from each speaker

at the listening position. For the front left, front

right, center, surround left, surround right and

surround back speakers, the output levels can

be adjusted between –12 to +12 dB.

The subwoofer can be adjusted between –18

and +12 dB.

These adjustments result will be stored to 7.1

CH. INPUT memory.

Adjust the main volume with the MAIN

VOLUME knob or the VOL buttons on the

remote controller.

To cancel the 7.1 CH. INPUT setting, press the 7.1

button on the remote controller.

Notes:

• When the 7.1 CH. Input is in use, you may not select

a surround mode, as the external decoder determines

processing.

• In addition, there is no signal at the record outputs

when the 7.1 CH. Input is in use.

• Furthermore, the following functions are not

available during 7.1 CH Input use.

Test Tone, NIGHT MODE, Source Direct, Pure

Direct, HT-EQ, Tone Control, Acoustic EQ.

AUX2 INPUT

If you don’t need to connect 7.1 Ch. input terminals

with multi channel decoder,

L(front left) and R (front right) inputs terminals are

available as AUX2 input.

In this case, You can connect additional audio source

to AUX2 as other audio input terminals.

VIDEO ON/OFF

When no video signal is connected to the unit or

a DVD, etc., is connected directly to your TV, the

unnecessary video circuit can be turned off by

selecting the “VIDEO OFF” setting.

To select video off, press the AMP button and press

the V.OFF button.

The “V-OFF” indicator on the front display panel will

light.

SR6003_U_01_ENG 3_4.indd 44SR6003_U_01_ENG 3_4.indd 44 08.8.1 1:08:03 PM08.8.1 1:08:03 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz SR6003 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantz SR6003

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info