Bedienungsanleitung Marantz SR7002 (Seite 49 von 94) (Englisch)

62166

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

ENGLISH

Note:

• The detection check measures the state of use of all

speakers whether actually used or not.

For example, if the center speaker is not used, the

test tone will require time to go from the L-channel

to the R-channel, therefore be careful not to unplug

the microphone or operate this unit during this

time.

When the 1 st Position Check ends, the

following OSD appears on the display.

AUTO SETUP

SPEAKERS CHECK:OK

2nd MIC POSITION!!

START

CHECK

CALCULATE

EXIT

Here, to view the results of the detection check,

select “CHECK” with the 3/4 cursor buttons

and press the OK/ENTER button. The results

will be displayed.

SPEAKER CONFIG

CHECK !! SPEAKER

FRONT : YES

CENTER : NON

FRONT R : YES

SURR.R : YES

SURR.B R : NON

SURR.B L : NON

SURR.L : YES

SUB W : YES

RETURN EXIT

If the check results indicate an error, take suitable

action with that item and remeasure. (For error

messages, see “ERROR MESSAGES” on

page 48.)

After confirming the check results, select

“RETURN” with the 3/4 cursor buttons and

press the OK/ENTER button to return to the

OSD menu.

At this point, you can select “EXIT” to end Auto

Setup and return to “2. SPKR SETUP”.

Note:

• AUTO SETUP is not available in Pure Direct,

Source Direct, or 7.1 Channel Input modes.

2-1 AUTO SETUP (MultEQ™ SETUP)

The AUTO SETUP (MultEQ™ Setup) feature of

the unit measures sound characteristics of the

speaker system and room where the unit is used and

automatically optimizes settings.

The Audyssey MultEQ™ technology adopted by

this unit provides the best listening environment for

multiple listeners.

To do this, the AUTO SETUP feature measures a

test tone emitted by each channel in a maximum of 6

listening positions, using the supplied microphone.

The measurement results are analyzed using an

original algorithm and environmental settings are

made to improve the sound characteristics of the

listening area.

To set up the speaker system (i.e., adjusting speaker

distance, etc.) without using the AUTO SETUP feature,

see “MANUAL SETUP” on page 49 of the manual.

HOW TO PERFORM AUTO SETUP

During measurement, the OSD menu displays the

condition, therefore turn power to the monitor on.

Connect the supplied microphone to the MIC

jack on the unit.

AV SURROUND RECEIVER SR8002

POWER ON/OFF PHONES

STANDBY

SL S SR

LFE

DIGITAL

SURROUND

DISP MULTI AUTO TUNED ST SPKR A B V-O FF

NIGHT

PEAK ANALOG

DIGITAL

ATT

SLEEP

SURR DIRECT

AUTO

DISC 6.1 MTX 6.1

PCM

AAC

AUX 1 INPUT

AUDIOS-VIDEODIGITAL VIDEO L R

DOWN

VOLUME

ENTER

INPUT SELECTOR

M-DAX

Set the microphone in the listening position.

Notes:

• Measurement can be done in a maximum of 6

listening positions.

For the ﬁ rst measurement, set the microphone in the

main listening position.

• Use a stand or tripod to position the microphone at

ear height in the listening position.

• Remove any obstructions between the speakers and

microphone.

• To use the internal subwoofer of the amp, set the

volume to the middle point and set the crossover

frequency to the highest.

• During measurement, step away from the microphone

and operate the unit via the remote controller from a

position that is out of the path of the speaker sound.

• The test tone output from the speakers during

measurement is loud. Be mindful of neighbors and

watch out for small children.

Select “2. SPKR SETUP” from the MAIN

MENU, select “AUTO SETUP” with the 3/4

cursor buttons, and press the OK/ENTER

button to display the start screen.

Select the number of channels for the surround

back speaker you are using.

For a 5.1 channel speaker system, select

“NON” (Surround Back speaker off). (To use

speaker C or multi speaker, select “NON”. See

page 38, 55.)

Select “START” with the 3/4 cursor buttons

and press the OK/ENTER button to start

measurement.

AUTO SETUP

AUTO SETUP: START

MAIN ROOM

SURR BACK: 2CH

RETURN EXIT

1 st Position Check

During the ﬁ rst position check, the following

screen is displayed as the unit checks

background noise in the listening room,

presence of speakers, and speaker polarity

and measures the acoustical characteristics in

the ﬁ rst position where the microphone is set

up.

AUTO SETUP

SPEAKERS CHECK:--

1st MIC POSITION

NOW ANALYZING !!

CANCEL

EXIT

Move the microphone to the second listening

position, select “START” with the 3/4 cursor

buttons and press the OK/ENTER button to

measure the second point. At this point, you

can cancel second point measurement and

calculate measurement results by selecting

“CALCULATE” and pressing the OK/ENTER

button.

AUTO SETUP

SPEAKERS CHECK:OK

2nd MIC POSITION!!

START

CHECK

CALCULATE

EXIT

Repeat steps 7 until measuring 6 points

between the main listening position and

surrounding positions.

When all measurements end, the following

OSD appears on the display.

AUTO SETUP

SPEAKERS CHECK:OK

CALCULATE

EXIT

Select “CALCULATE” with the 3/4 cursor

buttons and press the OK/ENTER button

to calculate measurement results. During

calculations, the following OSD appears on the

display.

AUTO SETUP

______________

NOW CALCULATING!

EXIT

Note:

• Less than 6 positions can be measured, but it is

recommended to measure in all 6 positions in order

to obtain the best results.

• The time needed to complete calculations depends

on the number of connected speakers and measured

listening positions. The more speakers and listening

positions, the more time is needed.

SR7002-8002_U_01_ENG 2_3.indd 46SR7002-8002_U_01_ENG 2_3.indd 46 07.8.24 1:15:23 PM07.8.24 1:15:23 PM

Marantz SR7002 Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantz SR7002

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info