Bedienungsanleitung Marantz SR7005 (Seite 85 von 128) (Englisch)

453910

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Basic versionSimple version Information

ENGLISHDEUTSCHFRANÇAISITALIANOESPAÑOLNEDERLANDSSVENSKA

Advanced version

Manual Setup

Remote control operation

buttons

Move the cursor

(Up/Down/Left/Right)

Conﬁrm the setting Return to previous menu

Setting items Setting details

Speaker Conﬁg.

(Continued)

F.Wide : Set the presence and size of the front wide speakers.

• Large : Use a large speaker that can adequately play back low

frequencies.

• Small : Use a small speaker that has inadequate playback capacity for

low frequencies.

• None : Select when the front wide speakers are not connected.

NOTE

When “Amp Assign” setting (vpage80) is other than “Normal”, you

cannot make the “F.Wide” setting.

Bass Setting

Set subwoofer and LFE

signal range playback.

Subwoofer Mode : Select low range signals to be reproduced by

subwoofer.

• LFE : The low range signal of the channel set to “Small” speaker size is

added to the LFE signal output from the subwoofer.

• LFE+Main : The low range signal of all channels is added to the LFE

signal output from the subwoofer.

• “Subwoofer Mode” can be set when “Speaker Conﬁg.” – “Subwoofer”

(vpage80) is set to “Yes”.

• Play music or a movie source and select the mode offering the strongest

bass.

• Select “LFE+Main” if you want the bass signals to always be produced

from the subwoofer.

NOTE

If “Front” and “Center” for “Speaker Conﬁg.” are set to “Large”, and

“Subwoofer Mode” is set to “LFE”, no sound may be output from the

subwoofers, depending on the input signal or selected surround mode.

LPF for LFE : Set LFE signal playback range.

• 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz

Distance

Set distance from listening

position to speakers.

Measure beforehand the

distance from the listening

position to each speaker.

Unit : Set the unit of distance.

• Feet / Meters

Step : Set the minimum variable width of the distance.

• 1ft / 0.1ft

• 0.1m / 0.01m

Front L / Front R / Center / Subwoofer / Surround L / Surround R /

S.Back L

/ S.Back R

/ F.Height L / F.Height R / F.Wide L / F.Wide R

: Select the speaker.

z When the “Speaker Conﬁg.” – “S.Back” setting (vpage80) is set to

“1spkr”, “S.Back” is displayed.

• 0.0ft – 60.0ft / 0.00m – 18.00m : Set the distance.

Setting items Setting details

Distance

(Continued)

• The speakers that can be selected differ depending on the “Amp Assign”

(vpage80) and “Speaker Conﬁg.” (vpage80) settings.

• Default settings :

Front L / Front R / Center / Subwoofer / F.Height L / F.Height R / F.Wide L /

F.Wide R : 12.0 ft (3.6 m)

Surround L / Surround R / S.Back L / S.Back R : 10.0 ft (3.0 m)

• Set the difference in the distance between the speakers to less than 20

ft (6.0 m).

NOTE

Speakers set to “None” in “Speaker Conﬁg.” (vpage80) are not displayed.

Default : The “Distance” settings are returned to the default settings.

• Yes : Reset to the defaults.

• No : Do not reset to the defaults.

When you select “Default” and press ENTER, the “Default Setting?”

prompt is displayed. Select either “Yes” or “No”, and press ENTER.

Channel Level

Set the volume of the test

tone to be the same when it

is output from each speaker.

Test Tone Start : Output test tone.

• Front L / F.Height L / Center / F.Height R / Front R / F.Wide R /

Surround R / S.Back R

/ S.Back L

/ Surround L / F.Wide L /

Subwoofer : Select the speaker.

z When the “Speaker Conﬁg.” – “S.Back” setting (vpage80) is set to

“1spkr”, “S.Back” is displayed.

• –12.0dB – +12.0dB (0.0dB) : Adjust the volume.

• When o is pressed while the subwoofer volume is set to “–12 dB”, the

“Subwoofer” setting switches to “OFF”.

• When “Channel Level” is adjusted, the adjusted values are set for all the

surround modes. To adjust the channel level separately for the different

surround modes, use the operation see page 58.

• When you press TEST TONE on the remote control unit, you can enter

this setting item immediately.

NOTE

• Speakers set to “None” in the “Speaker Conﬁg.” (vpage80) settings

are not displayed.

• When a headphones jack is inserted in the PHONES jack of this unit, the

“Channel Level” is not displayed.

Default : The “Channel Level” settings are returned to the default settings.

• Yes : Reset to the defaults.

• No : Do not reset to the defaults.

When you select “Default” and press ENTER, the “Default Setting?”

prompt is displayed. Select either “Yes” or “No”, and press ENTER.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marantz SR7005 Seite 85

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Marantz SR7005

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info