161017
31
Zoom out
Zoom in
Vorherige Seite
1/35
Nächste Seite
27
ENGLISH
7
Sleep timer
The sleep timer function allows the unit to be in standby
mode automatically after specific period of time.
1. Press the SLEEP button m on the remote control.
2. Each press of the button will increase the time before
shut down in the following sequence.
3. The sleep timer will be shown for 5 seconds in the
display, and it will count down until the time has elapsed.
When the programed sleep timer has elapsed, the unit
will automatically turn off.
Note that the display will be dimmed when the sleep
timer is programed.
4. Press the SLEEP button m. The display shows the
remaining time until standby mode begins.
5. To cancel the sleep timer, press the SLEEP button m
repeatedly until the display shows "SLEEP OFF".
When the sleep timer is programed, DIMMER function
does not activate.
10
20
30 60 90 120OFF
OTHER OPERATION
REMOTE CONTROLLER
RC7001ST
SHIFT
R
E
E
N
T
BAND MENU
TUNING
CONTROL
CHANNEL/
A/B C/D E/F
TIMER
10
DISPLAYDIMMER
987
456
32
T-MODEI/JG/H
SLEEP MEMO
ONSTANDBY
1
/A-TUNE
A-PRESET
m
LAST FUNCTION MEMORY
This unit is equipped with a last function memory which
stores the input and output setting conditions as they were
immediately before the power is switched off.
This function eliminates the need to perform complicated
resettings when the power is turned on.
The unit is also equipped with a back-up memory.
This function provides approximately one week of memory
storage when the main units power switch is off and with
the mains cord disconnected.
INITIALIZATION OF THE
MICROPROCESSOR
When the indication of the display is not normal or when
the operation of the unit does not shows the reasonable
result, the initialization of the microprocessor is required
by the following procedure.
1. Unplug the mains cord from the power outlet after
pressing the POWER ON/STANDBY switch q and
setting the standby mode.
2. Holding both the DIMMER button r and MENU button
u, plug the mains cord into the power outlet.
3. Check that the entire display is flashing with an interval
of about 1 second, and release your fingers from the 2
buttons and the microprocessor will be initialized.
Note
If step 3 does not work,start over from step 1.
If the microprocessor has been initialized all the button
settings are reset to the default values (the values set
upon shipment from the factory).
PUSH ENTERPUSH ENTER
TUNING/PRESETTUNING/PRESET
STEREOSTEREO
RDSRDS
TUNEDTUNED
SECONDARYSECONDARY
BAND SELECTBAND SELECT
AUTO TUNEAUTO TUNE
MENUMENU
DISPLAYDISPLAY
DIMMERDIMMER
STANDBYSTANDBY
ON/STANDBYON/STANDBY
POWERPOWER
DAB/FM/AM TUNER ST7001DAB/FM/AM TUNER ST7001
q r u
ST7001N 01 Eng 05.7.21 5:24 PM ページ27
31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Marantz st7001 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info