Bedienungsanleitung Marder schreck 16277 (Seite 6 von 14) (Deutsch, Englisch, Holländisch, Französisch)

807594

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

6.2 PREPARATION

Clean the engine compartment thoroughly or use the primer spray for

removing marten scent marks, item number: 16265 before installing

the ultrasound marten repellent device. We also recommend cleaning

the underside of the vehicle and the site on which it stands.

CAUTION

Before starting with the installation of the ultrasound marten

repellent device, read the instructions in the manual of your

vehicle regarding disconnecting the battery. Disconnecting the

battery may result in information in the on-board computer

and radio settings being lost.

6.3 ASSEMBLY

Install the ultrasound marten repellent device in such a way that the

sound is able to spread freely, similar to the light cone of a torch. Select a

position, g.2, that is as high up as possible in the engine compartment

to prevent the risk of inuence from dirt and water. Ensure a good dis-

tance is left between the device and heat sources such as the exhaust,

catalytic converter and rotating parts. Make sure that the fuse in the

connecting cable is easily accessible. In very tight engine compartments,

it may be necessary to install multiple martin repellent devices since the

ultrasound can be shielded considerably by obstacles.

Figure 2: Mounting

6. OPERATING INSTRUCTIONS

6.1 OVERVIEW

1 Control lamp high voltage

2 Control lamp operation

3 Loudspeaker opening

4 Mounting lugs

5 Control cable, green

6 Plus (+) cable, red

7 Minus (-) cable, black

8 High voltage cable

Figure 1: Overview

Lay the high-voltage cable in such a way that there are bare metal parts

with a ground connection nearby, (g. 3). The repelling eect is only

guaranteed if the marten touches a contact plate and grounded parts at

the same time.

Figure 3: High voltage cable

6.4 ELECTRICAL CONNECTION

Disconnect the battery.

Lay the cables so that they are not under tension and cannot

be kinked or crushed. Keep away from heat sources such as

exhaust, catalytic converter and rotating parts. Secure the

cables well and safely.

The control cable is connected to the ignition plus and ensures that the

unit switches o when the vehicle is started. If you do not connect this

cable, the unit is in continuous operation. This continuous operation

is not permitted within the scope of the German Road Trac Licensing

Regulations (StVZO).

Plus (+) connecting cable, red (6) to permanent plus (terminal 30)

Minus (-) connection cable, black (7) to earth (terminal 31)

Control cable, green (5) to ignition plus (terminal 15)

Remove the screw above the hole for the high-voltage cable from each

contact plate (Fig. 4).

Figure 4: Remove screw

Pass the high-voltage cable through the small hole in the insulator on all

contact plates (Fig. 5).

Figure 5: High-voltage cable through insulator

When you have xed all contact plates, put the screws back in (picture 6).

Screw the screws all the way in. The screw penetrates the insulation of

the high-voltage cable. This makes an electrical connection between the

cable and the contact plate.

Figure 6: Screw in the screw

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marder schreck 16277 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info