Bedienungsanleitung Marmitek AFX3 (Seite 4 von 5) (Englisch, Holländisch)

494334

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

home automation modules & components

• Connection of the Marmitek X-10 module to the wrong mains

voltage.

• Opening of the Marmitek X-10 module's housing (with the

exception of types RFIX and IRIX that may be opened for

installation purposes).

• Modification or repair of the Marmitek X-10 module or wiring

or any attempt to do so.

• The Marmitek X-10 module becomes defective as a result of

connecting potential to the potential-free connecting wires of

the Marmitek X-10 module.

• Defects resulting from rough handling of the Marmitek X-10

module or

• Defects caused by using the wrong fuses or bridging fuses.

Limitation of liability

Except in the event of liability arising from the law, Marmitek is

not liable for direct damage, material damage or damage to

persons, including consequential damage.

Marmitek is not liable for any indirect damage, immaterial

damage or consequential damage whatsoever, including but not

limited to loss of revenue, damage caused by interruption to

production, loss of profits, pure pecuniary damage etc.

Area of application for XANURA home automation

Marmitek is a home automation system that has been designed

to be used exclusively in the housing sector. The area of

application for Marmitek X-10 modules must therefore remain

restricted to residential buildings and the housing sector. It is

not permitted to use Marmitek X-10 modules in the open air or

in humid environments. The system is exclusively intended for

use under the following environmental conditions:

X-10™ home automation

Power supply 230 Vac, 50 Hz

Minimum ambient temperature 0 °C

Maximum ambient temperature 40 °C (*) (**)

Atmospheric pressure 86 pkA - 106 pkA

Relative air humidity (non-condensing) 30 tot 90%

(*) Marmitek X-10 modules are suitable for use in residential environments at

ambient temperatures normally not exceeding 35 °C, occasionally reaching 40

°C.

(**) The maximum load for dim and switch actuators also depends on the ambient

temperature. Please carefully read the instructions for load reduction of dim and

switch actuators before using the Marmitek X-10 modules. The instructions are

enclosed with the dim and switch actuators.

Before starting the installation

Before installing a module, you must make sure that the module

is suitable for the intended application. If in doubt, contact a

qualified installer, specialist or the manufacturer for advice.

Instructions for installation & connection of modules

General installation and connection instructions

PLEASE NOTE: Disregarding the following instruc tions

can considerably shorten the service life of the

Marmitek X-10 modules and will render the guarantee

void! It is recommended to use a certified installer.

1 Use of modules to be restricted to the housing sector

2 Always disconnect the power before installing modules

3 Install in junction box or distribution box (or box with

comparable properties), covered with a cover plate or

switching device.

4 Make sure the live and neutral connections are correct!

5 One module per junction box/distribution box

6 The temperature of the module in the box used may

increase by a max. of 10 °C.

7 Never cover modules with insulation material

8 Pay attention to the proximity of heat sources

9 Prevent potential-free connecting wires from coming into

contact with live components (insulate live components)

10 Do not use objects or force during installation

11 Tightening torque for screws - max. 0.5 Nm

12 Keep modules accessible for programming and maintenance

• Always switch the power off before installing the module.

• If the live and neutral wires are connected to the module in

reverse, 230 V will be released on one of the module's

potential-free connecting wires! Make sure that the live and

neutral wires are connected correctly to ensure your safety

and the safety of others, see Figure 1.

PROG.

DAIX

Figure 1.

• Connect the live wire (2) to the L side of the Marmitek X-10 module, and the

neutral wire (3) to one of the neutral terminals.

• Connect the other neutral terminal (4) of the Marmitek X-10 module to the neutral

of the wall socket.

• Connect the dimmed output of the Marmitek X-10 module (5) to the live terminal of

the wall socket.

Instructions for installation & connection of modules

• Marmitek built-in modules must be installed in a junction box or

distribution box.

• Other enclosures comparable to junction boxes and distribution

boxes are permitted as long as they meet the following criteria:

■

In these enclosures, the Marmitek built-in module and other

built-in components or equipment should not cause a

temperature increase within the enclosure that exceeds 10 °C.

■

Thermal properties at least equal to those of a junction

box/distribution box.

■

Flame resistance at least equal to that of a junction

box/distribution box.

• Only one Marmitek X-10 module to

be installed per junction

box/distribution box. Besides one

Marmitek X-10 module, no other

heat generating components may

be installed in the same junction

box. The installation of several

Marmitek X-10 modules in a single

junction box can lead to the

Marmitek X-10 modules

malfunctioning or becoming

prematurely defective.

Marmitek AFX3 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info