Bedienungsanleitung Marmitek EasyTouch Panel10 X-10 (Seite 11 von 65) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

494263

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

9Easy Touch Panel 10™

8. FREQUENTLY ASKED QUESTIONS

What is the reason for modules to switch on/off spontaneously?

It is possible that a Marmitek X-10 System is installed at one of your neighbours using the same House Code. To solve

this problem try to change the House Code of your system, or have FD10 Phase Coupler/Filter installed at your incoming

mains.

My modules will not respond to my controller.

Make sure that the House Code on all Modules and Controllers are set to the same House Code (A .. P).

My modules will not react to my remote / sensor.

When you use a remote or sensor, you should have at least one TM13 Transceiver or Marmitek X-10 Security Console

installed in your house. These components will translate the radio signals to the Marmitek X-10 signal on the power line.

Using several remotes and sensors, you only need one central transceiver.

Am I able to increase the range of my remotes by using more Transceivers?

Yes, you can use more than one TM13 Transceiver in your home when the range of your remotes is not sufficient. The

TM13 is using so called collision detection to prevent signals to be disturbed when more than one TM13 is transmitting.

TM13’s will wait for a quite power line before transmitting their data. To prevent your Marmitek X-10 System to become

slow or to prevent dimming from becoming less smooth, make sure that the TM13 units are placed as far away from

each other as possible.

I have defined a button but if I press this I hear a short beep but nothing happens.

The EasyTouch Panel 10 ensures that, after touching the screen, the corresponding Marmitek X-10 code is sent wirelessly.

This signal must be received by a Marmitek X-10 transceiver which then places this signal on the power line and can

then operate a module. Check whether your transceiver is receiving this by using a TM13 and defining, for example, a

TOGGLE button which is set to the house code of the TM13 and unit code 1. If you touch this button on the screen,

leaving a slight pause of 1 second between each touch, you should be able to hear the TM13 switch. If you have used

several house codes together, ensure that you also use several TM13 modules, each of which is set to a house code that

has been used. Or set the house code of your TM13 to house code P. Then, the TM13 will place ALL received house

codes on the power line.

I cannot find the selections ‘ALL LIGHTS ON’, ‘ALL LIGHTS OFF’, ‘ALL UNITS OFF’, ‘DIM UP’ and ‘DIM DOWN’.

These functions are not bound to a unit code. If you wish to programme these functions, browse through the unit codes

(1...16). You will find the above functions after unit code 16.

How can I move a button?

You move a button by deleting the existing button and adding it again.

How can I clean the screen?

You can use a clean, soft, lint-free cloth which you can moisten slightly with distilled water. Do not spray any fluids

directly onto the screen.

Do you still have questions? Please check out www.marmitek.com for more information.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marmitek EasyTouch Panel10 X-10 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info