Bedienungsanleitung Marmitek IRIX35 (Seite 8 von 8) (Englisch, Holländisch)

494327

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Problem: LED does not flash when I press the remote control.

Cause: The remote control batteries are (almost) flat.

Solution: Replace the batteries.

Cause: The remote control is not in the Infrared mode.

Solution: Switch the remote control to IR transmitter.

Cause: The infrared signals are not received.

Solution: Reduce the distance between transmitter and receiver.

Problem: The infrared receiver only works when the remote control

is used at a short distance from the infrared receiver.

Cause: The remote control batteries are (almost) flat.

Solution: Replace the batteries.

Cause: The sun or high frequency (fluorescent) lighting is shining directly

onto the infrared receiver and interfering with the infrared receiver.

Solution: Move the infrared receiver and ensure that it is not directly

exposed to the sun or this lighting source.

Troubleshooting

Troubleshooting (cont'd.)

Problem: After the remote control batteries are replaced, I cannot

operate anything.

Cause: The remote control batteries are incorrectly positioned or make

insufficient contact.

Solution: Check if the batteries are correctly positioned.

Problem: When I want to dim the lamp, the lamp switches on or off

instead of dimming after I have pressed a number on the

remote control.

Cause: The IRIX35 is in the IR-toggle mode.

Solution: Switch the IRIX35 to the standard mode.

Problem: The modules in the house do not switch when I press the

remote control.

Cause: The IRIX35 is set to an incorrect letter code.

Solution: Switch the receiver to the correct letter code.

Problem: Now and then, I have to press the remote control twice

before a module switches or carries out a command.

Cause: The IRIX35 is programmed to the IR-toggle mode and does not

perform "Address Learn Mode" well.

Solution: Carry out "Address Learn Mode" again.

Problem: The "Address Learn Mode" cannot be performed well.

Cause: Commands from other (Marmitek X-10) components are

transmitted via the lighting circuit and disrupt the learning

process of the infrared receiver.

Solution: Switch all other (Marmitek X-10) components off, such as

movement sensors, computer interface and Home Control Box etc.,

so that they cannot transmit via the lighting circuit during the

learning process. Do not operate any switches during this process.

Electrical equipment and systems can be sensitive to signals from

other equipment, which causes electro magnetic disturbance. In

the European Union, countries agreed upon laws for the immunity

(sensitivity) of signals of other equipment as well as equipment

emission (disturbance). When equipment or applications in a certain

surrounding comply with the valid standards, they will not disturb

each other's operations (they are called "Electro Magnetic

Compatible").

For residential surroundings, where the home automation system

Marmitek X-10 is being applied, the European standard for

immunity is standardised in EN 61000-6-1. Equipment that complies

with this standard is resistant to electro magnetic emission of other

equip ment, which complies with the European standard EN 61000-

6-3 for residential surroundings. Experience has shown that in

domestic surroundings, equipment is being used which has an

EMC-emission level that is above the levels stated in EN 61000-6-3.

This equip ment can disturb the correct functioning of the Marmitek

X-10 modules. The immunity of the Marmitek X-10 built-in modules

is therefore revaluated and equivalent to EN 61000-6-2 (the more

severe European standard for immunity in industrial surroundings).

Nevertheless, the application area for Marmitek X-10 will

remain restricted to residential areas.

Undisturbed functioning of Marmitek X-10 automation

Marmitek X-10 is therefore not responsible for the disfunctioning

of the Marmitek X-10 system as a consequence of equipment in

the building with emission levels that exceed the maximum

allowed levels set as standard for residential, commercial and

semi-industrial surroundings stated in EN 61000-6-3.

Application area Valid European Standard Marmitek X-10

home automation*

Immunity of Emission of Immunity and

equipment equipment

emission standards

Residential 61000-6-1 61000-6-3 Compatible/

Commercial meets the

Semi-industrial requirements

* Condition is that the total Marmitek X-10 system is installed in accordance

with valid instructions supplied by a certified and trained Marmitek X-10

dealer.

Copyrights

Marmitek is a trademark of Pattitude B.V., IRIX35™ is a trademark of Marmitek B.V.

content (including but not limited to model numbers, software, audio, video, text and

photographs) rests with Marmitek B.V. Any use of the Content, but without limitation,

distribution, reproduction, modification, display or transmission without the prior

written consent of Marmitek is strictly prohibited. All copyright and other proprietary

notices shall be retained on all reproductions.

20324 - 20100929

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marmitek IRIX35 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info