Bedienungsanleitung Marmitek PC CONTROL REMOTE (Seite 11 von 56) (Deutsch, Englisch, Holländisch, Französisch)

613067

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

11PC CONTROL

The search starts after the last registered code. If that was 030, the search starts at 031

until the last possible code and then goes from 000 to 029.

Note: if certain functions of your equipment can’t be controlled you will have to find a

different code for your brand.

4.4. Automatic code search

When searching an unknown code, you can step through the library automatically

(AutoSearch). When your equipment responds, you can stop the searching process and

store the code you found.

Note: as you can dedicate any appliance (TV, DVD, SAT...) to VCR, DVD, SAT or AUX keys,

you need first to enter any 3 digit code for the kind of appliance you wish to control

(found in the code book), i.e.: If you want to program a SAT under the VCR key, enter

ANY SAT code found in the code book and then follow the steps below:

1. Turn on the device you want to control.

2. Press and hold SETUP (4) until the LED indicator (2) lights steadily.

Release SETUP button.

3. Press the mode button (3) that matches the equipment you wish to control.

The LED (2) blinks once.

4. Press Channel+ (9) once. After a few seconds the remote starts stepping through

the code library (fast search, 1 code per second). When the device responds, you can

press Channel+ (9) to switch to slow search (1 code per 3 seconds). You can step

back by pressing Channel- (9) (you can step forward by pressing Channel+ (9) in

case you went too far back). As soon as the device responds again, press the --/- key

(14) to store the code you found.

4.5. Brand search

If your brand is listed hereafter, you have the possibility to use the brand search method

(faster than the "manual" and the "automatic code search").

BRAND CODE BRAND CODE

Philips/Radiola 1 Telefunken/Saba/Normende 4

Sony/Panasonic/JVC/Sharp 2 Grundig/Blaupunkt 5

Akai/Toshiba/Daewoo

Thomson/Brandt 3 Nokia/ ITT 6

1. Turn on the device you want to control.

2. Press and hold SETUP (4) until the LED indicator (2) lights steadily.

Release SETUP button.

3. Press the mode button (3) that matches the equipment you wish to control.

The LED (2) blinks once.

Enter the code corresponding to your brand, point the PC Control Remote in

the direction of your equipment, press Channel+ (9) once only. Continue to point the

PC Control Remote at your equipment until the equipment changes channel (the

remote control sends an IR signal every second. Please wait until your equipment

reacts). When your equipment does react, press on the key --/- (14) to confirm. If you

accidentally miss the code, you can stop the autosearch by pressing Channel- (9) and

by repeatedly pressing this key return to the right code. Press --/- (14) to confirm.

4.6. Identifying codes found

1. Press and hold SETUP (4) until the LED indicator (2) lights steadily. Release SETUP.

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marmitek PC CONTROL REMOTE Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info