Bedienungsanleitung Marmitek SD Memory2 (Seite 8 von 64) (Holländisch)

97347

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

8 © MARMITEK

2. INSTALLATION

Connecting the cameras:

• Secure the camera at any suitable wall that you desire (fig. 2, 3 and 4).

• Connect the 4 pin DIN plug of signal & DC cord ‘D’ to the camera (fig.4).

•

Connect the yellow RCA jack of signal & DC cord ‘D’ to the A/V terminal ‘CH1’ of the SD recorder (fig.4).

Connecting the power adapters (see fig. 4):

• Connect the DC plug of DC power cord splitter ‘E’ to ’DC IN’ connector of the SD recorder.

• Connect the female DC connector (plug with hole connector) of signal & DC cord ‘D’ to one of the

two remaining male DC plugs (plug with pin connectors) of DC power cord splitter ‘E’.

• Connect the female DC connector of DC power cord splitter ‘E’ to the DC adaptor.

Connecting to TV or monitor (see fig. 4):

• Connect the yellow RCA jack of A/V cable for video output ‘F’ to the A/V terminal on the back of the

SD recorder and connect the other yellow plug to the video-in connector of your TV.

• Connect the white RCA jack of signal & DC cord ‘D’ to the audio input of your TV.

Connecting to TV or monitor using a SCART adapter (option):

When your TV doesn’t have an RCA A/V input but it does have a SCART connector, then you can connect

the SD recorder using an optionally available SCART adapter (Art. no: 27023 Marmitek SCART adapter

Receiver). (Please see fig. 5 for connection).

Connection to alarm output:

The NO (normally open) outgoing signal can activate an external alarm (the Normally Open contact closes for

about 10 sec. in case of an alarm). See the specifications of your alarm system for the connections (see fig. 6D).

Upon that, in combination with the Marmitek X-10 components, you can use this connection to switch a

(outside) light for example. Requirements for a simple connection are

(see fig. 6A)

SM10 (converts the SD recorder signal into a X-10 signal and puts it on the mains)

Art nr. SM10: EU: 08943, UK: 09552

AM12 or LM12 (receives the X-10 signal and switches the lights on or off)

Art nr. AM12: G: 08915, U:08978, I:09052, F:08916, CH:09249

Art nr. LM12: G: 08910, U:08977, I:09051, F:08911, CH:09248

For more information on the X-10 protocol and the use of it, visit our website http://www.marmitek.com.

Use of the external ‘trigger’ contact:

Every alarm contact can be connected to this input, in the form of a potential-free NO (normally open)

or NC (normally closed) contact, e.g. magnetic door/window contacts, motion detectors, etc. Multiple

detectors can be connected to the trigger contact, to activate the SD recorder and to start a recording

(serial for NC, parallel for NO alarm contacts)

(see fig. 6C)

For example, to have the SD recorder start recording due to a signal from an external Marmitek motion

detector, you will need the following components

(see fig. 6B)

SM10 AM12 LM12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marmitek SD Memory2 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info