Bedienungsanleitung Marmitek TV Anywhere (Seite 11 von 108) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

489106

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

ENGLISH

11TV Anywhere™

5. PROGRAMMING THE 6IN1 AS A UNIVERSAL REMOTE

The 6in1 remote control provided does not only control your TV Anywhere system you can

also control your TV, VCR, DVD player and satellite receiver with this remote. The remote

control is pre-programmed at the factory for most brands and models.

5.1 Programming the remote control for your TV, Set-Top Box, DVD player and

satellitereceiver

To make your remote control suitable for your own equipment, you have to program it once.

You can do this by entering a code, related to the brand and type of equipment you want to

control. You can program any device under any MODE button. For example, if you have two

Set-Top Boxs, you can program Set-Top Box 1 under VCR and Set-Top Box 2 under DVD.

5.2 Manual code entry

Take your code book and search for the list matching the device you are looking for, e.g. TV

or Cable. Next, find the relevant brand (e.g. Sony). Now you will see one or more codes. If

there is more than one code, it depends on your equipment which code is correct. Generally,

the codes are displayed in order of age of the device. Older devices first, newer devices last.

Sometimes you will have to try several codes before you find the right code for your device.

1. Make sure your device is switched on (for example the TV).

2. Press and hold SETUP [7] until the LED indicator stays lit. Release SETUP .

3. Press and release the mode button [3] of the device you want to control (for example

TV).

4. Enter the code from the code book by using the key pad [9]. The LED [2] will extinguish

after the last digit is entered. If you have entered a wrong code, the LED will flash for 3

seconds and then extinguish. You have to repeat steps 2-4.

5. Point the remote at your TV and press the POWER button [1]. Your device should now turn

off. Check other functions (for example for a VCR FF or REW, etc.). If certain functions

are not responding, the entered code is not the correct one. In that case repeat the steps

above with the next corresponding code of your brand.

6. Repeat this procedure from step 1 for the other devices you want to control (VCR, DVD,

SAT,...).

5.3 Automatic code search for some well-known brands

If your brand is listed below, you can use the brand search method (faster than the “manual”

and the “automatic code search”).

1. Turn on the device you want to control.

2. Press and hold SETUP [7] until the LED indicator [2] stays lit. Release SETUP.

3. Press the mode button (3) that matches the device you wish to control. The LED [2] will

flash once.

4. Enter the code for your brand, point the TV Anywhere Remote at your device and press

Prog+ [5] once. Continue to point the TV Anywhere remote control at your equipment

until the equipment changes Channel. (The remote control transmits an IR signal every

second. Please wait until your device reacts) When your device does react, press ENT [11]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marmitek TV Anywhere Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info