Bedienungsanleitung Marshall DSL40CR (Seite 5 von 38) (Deutsch, Englisch, Französisch, Spanisch)

705282

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

FRONT PANEL FUNCTIONS (CONT.)

ENGLISH

EQUALISATION SECTION

10. TREBLE

Controls the higher frequency content

of your sound. Turning clockwise will

increase the highs making the sound

brighter and more crisp.

11. MIDDLE

Controls the middle frequency of your

sound. Turning clockwise adds girth.

Turning anclockwise reduces the

middle frequencies ‘scooping’ your

sound – this is accentuated when used in

conjuncon with Tone Shi.

(Front Panel Funcon #13).

12. BASS

Controls the amount of lower frequency,

or boom-end, in your sound. Turning

clockwise will increase the boom-end

making the sound fuller.

13. TONE SHIFT

Tone Shi recongures the preamp EQ

network adding a new dimension to

tonal shaping.

Tonal Note: The preamp EQ network is

dynamic and highly interacve. Please note

that because of this, altering the seng of

one control can change the way that the

other controls behave – experiment to nd

your sound.

14. PRESENCE

Controls the amount of higher

frequencies of your sound. Turn

clockwise to add crispness and bite

for a more cung tone. PRESENCE

is a power-stage funcon and acts

independently of the preamp EQ

controls.

15. RESONANCE

Controls the amount of lower

frequencies in your sound. Turning

this control clockwise adds a resonant

bass boost, increasing boom-end.

RESONANCE is a power-stage funcon

and acts independently of the preamp

EQ controls.

REVERB SECTION

16. REVERB CLASSIC

Controls the REVERB level of the

CLASSIC GAIN Channel.

17. REVERB ULTRA

Controls the REVERB level of the ULTRA

GAIN Channel.

MASTER VOLUME SECTION

18. MASTER SELECT

This switches between MASTER 1 and

MASTER 2.

Note: You can switch between MASTER 1

and MASTER 2 using the oponal 6-way

PEDL-91005 footswitch.

19. MASTER 1

Controls the overall volume level of the

amplier when selected.

20. MASTER STATUS LED

This LED lights green to indicate that

MASTER 1 is selected and red to indicate

MASTER 2 is selected.

21. MASTER 2

Controls the overall volume level of the

amplier when selected.

22. LOOP STATUS LED

This LED lights red to indicated that the

FX LOOP is On. It is unlit when the FX

LOOP in O.

23. LOOP ON/OFF

This switch acvates and deacvates the

FX LOOP.

Note: FX LOOP On/O is footswitchable

ENGLISH

FRONT PANEL FUNCTIONS (CONT.)

The DSL100HR and DSL40CR are

supplied with a 2-way footswitch (PEDL-

90012) for channel select and FX loop

on/o.

There is also a 6-way footswitch

(PEDL-91016) available that enables

you to fully control your DSL100HR or

DSL40CR during performance. You can

select each mode: CLEAN, CRUNCH,

OD1 or OD2, as well as select MASTER

1 or MASTER 2, and switch the FX LOOP

On/O.

DSL FOOTSWITCHING

using the supplied 2-way footswitch or the

oponal 6-way footswitch.

24. OUTPUT

This three posion rocker switch

combines STB (standby) and HIGH/

LOW output power funcons. The

output stage and power control for this

amplier has been designed to deliver

the opmum tonal performance at

all power levels. The HIGH and LOW

output funcons allow the user to

choose between two conguraons of

the internal power supply. These two

conguraons give the choice between

two output power levels, but ensure that

the output valves behave in the same

way for both. This means the amplier

can be put into LOW power mode

without compromising on tone.

HIGH: This is the 100 Wa seng for the

DSL100HR and the 40 Wa seng for the

DSL40CR.

STB (standby): This is used in conjuncon

with the mains POWER switch (Front Panel

Funcon #25). When powering up, always

switch mains POWER on rst, leaving

the OUTPUT switch in the STB (standby)

posion. Standby mode should also be

used to mute the amp during breaks in

performances to avoid stress to the valves

of the amplier.

LOW: This is the 50 Wa seng for

the DSL100HR and the 20 Wa for the

DSL40CR.

25. POWER

Mains power ON/OFF switch.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marshall DSL40CR Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info