Bedienungsanleitung Marshall JVM215C Combos (Seite 10 von 60) (Deutsch, Englisch, Französisch, Spanisch)

705298

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ENGLISH

Rear Panel Operation

SERIAL / PARALLEL FX LOOP (12)

The JVM is equipped with a series / parallel FX

loop. Connect your external FX equipment input

to the JVM SEND jack, and the FX output to the

JVM RETURN jack. As described previously,

this effects loop can be bypassed from the front

panel and the amount of effect can be dialed in

with the MIX control.

The +4dBu/-10dBV switch allows you to

configure the loop for its use with either

professional equipment (+4dBu setting) or with

guitar level effects like effects pedals (-10dBV

setting).

When MIX is set to WET all the signal goes

through the external loop, adding more direct

(unprocessed) signal as you turn it towards

DRY. This allows you to mix any amount of the

external effect without loosing or degrading the

direct signal quality.

When mixing the WET and DRY signals the

external effects processorʼs output should be

configured to remove the direct (unprocessed)

signal or unpleasant phasing effects may occur

when mixing it again in the amplifier. If the

amplifier sounds thin after connecting an

external effect check that no direct signal is

being returned from the processorʼs output.

Note that if the FX loop is ON and the MIX

control is set to WET without an external

processor connected, the amplifier will be

muted.

POWER AMP INSERT / SERIAL LOOP (13)

This is a passive loop connected right before the

master controls. It is a line level loop so it is

recommended to only use high headroom

devices to avoid signal degradation. Plugging

only into the return jack allows the use of the

JVMʼs power section overriding the preamp.

Master controls and the emulated line out are

located after the serial loop so it is still possible

to take advantage of those features when using

an external preamplifier. The loop can be taken

off the circuit by pressing the BYPASS switch,

but as opposed to the Series / Parallel loop this

switch cannot be programmed.

EMULATED LINE OUT (14)

The pre master volume signal, processed

through a 4x12 speaker cabinet emulator and

electronically balanced is made available at this

connector.

FOOTSWITCH (15)

Connect the supplied footswitch using any

standard 1/4" jack mono lead. Using any other

type of footswitch rather than the supplied will

have no effect and will be ignored by the

amplifier.

MIDI In / Through (16)

Connect any external MIDI equipment to the

MIDI In DIN socket. A copy of the signal in this

connector will be available on the MIDI thru

socket to allow daisy chaining of MIDI

equipment. Note that the JVM only accepts

incoming data and it is not able to send any

MIDI commands.

SPEAKER Outputs (11)

There are 5 speaker outputs available on the

rear panel. They are labelled according to the

intended impedances:

16 Ohm: connect any 16 Ohms guitar cabinet to

this jack.

8 Ohm: connect a single 8 Ohms guitar cabinet

or two 16 Ohms guitar cabinets.

4 Ohm: connect a single 4 Ohms guitar cabinet

or two 8 Ohms guitar cabinets.

WARNING: Although the JVM amplifier has 5

speaker outputs, never attempt to connect more

speakers than rated. The safe combinations are

1x16 Ohm, 1x8 Ohm, 1x4 Ohm, 2x16 Ohm or

2x8 Ohm. Any other speaker configuration may

stress the power amplifier section and in

extreme cases may lead to valve and/or output

transformer failure.

HINTS & TIPS

Factory Reset

This will erase all the MIDI presets and set MIDI

reception channel to #1. Please note that once

the memory is erased it cannot be recovered.

Switch the amplifier off (power switch off, not

standby switch).

Press and hold CLEAN/CRUNCH CHANNEL

switch.

Switch the amplifier on (power switch on, not

standby switch).

The 2 channel LEDs will glow red.

Release the switch.

JVM 2 Ch Owners Manual Book-00089-01 /12/15 inner.qxd:Layout 1 14/12/15 10:08 Page 8

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marshall JVM215C Combos Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info