Bedienungsanleitung Marshall MG15FX Gold (Seite 5 von 57) (Deutsch, Englisch, Französisch, Spanisch)

705314

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

MG15FX & MG30FX OVERVIEW

CHANNEL SELECTION

The amplifier has 4 channels - Clean,

Crunch, OD-1 & OD-2.

Pressing the Clean/Crunch switch (3)

selects between the Clean (Green Light)

and Crunch (Red Light) channels.

Pressing the OD-1/OD-2 switch (5)

selects between the OD-1 (Green Light)

and OD-2 (Red Light) channels.

When moving from an OD channel

to a Clean/Crunch channel, the unit

remembers the last channel you were in

before leaving. E.g. If you have moved

from the Crunch Channel to an OD

channel and you press the Clean/Crunch

switch (3), the amplifier will revert back to

the Crunch channel - rather than starting

again in the Clean channel.

MODES

The amplifier operates in two modes -

Preset and Manual.

To change between these two modes, you

must hold the Tap switch (10) down for at

least two seconds. When in manual mode

the Store switch (12) lights red and the

selected channel light (3 or 5) will start to

flash.

The amplifier will remember the last mode

it was in after power off and revert to it

the next time it is powered on.

PRESET

This is the factory default operation of the

amplifier.

In Preset mode the position of all controls

except Master Volume (13) are stored

within each channel. Each channel should

be considered a preset.

Selecting a channel automatically recalls

the settings stored within the channel.

Note: The physical position of the front

panel controls, except Master Volume

(13) which is not storable, will now not

match the actual settings of the amplifier.

All front panel switches will automatically

update.

Altering a control will cause the associated

parameter to jump to the current physical

position of that control.

When a control is altered the selected

channel light (3 or 5) will start to flash

indicating that the current preset has been

altered.

To store the updated settings, push the

Store switch (12).

If you select another channel without

pressing Store (12) then any altered

settings will be lost as the new channel

and its settings are recalled.

MANUAL

In manual mode the amp’s settings always

match the physical positions of the

controls.

Changing channel only changes the

channel, NO presets are recalled, NO

other controls are altered.

Pressing Store (12) will store the current

settings into the selected channel. These

can then be recalled when using the unit

in Preset mode.

When channel settings have been stored

the current channel light (3 or 5) will stop

flashing indicating the preset has been

saved.

REVERB & FX

The amplifier provides two simultaneous

digital effects, Reverb (Studio or Spring)

and one of five FX (Chorus, Phaser,

Flanger, Delay or Octave).

REVERB

The Reverb control (8) sets the amount

of signal sent to either one of the two

ENGLISH

reverb options - Studio or Spring When

the Reverb control (8) is set to ‘0’ the

reverb is switched off, the status of the

reverb is also indicated on the optional

footcontroller.

The FX control is essentially split into five

segments and selects the type of FX and

adjusts its associated settings - except

in the case of Octave which has a simple

setting. When the FX control is set to

‘0’ the FX are switched off, the status of

the FX is also indicated on the optional

footcontroller.

TAP TEMPO

The Tap Tempo switch (10) is used for the

Delay effect only.

The Tap Tempo switch matches the delay

time to the time between two presses.

The Tap Tempo LED flashes red at the

selected/recalled delay time.

The number of repeats is reduced as the

delay time decreases.

If you change from a channel with delay

to one without delay the effect will spill

between channels.

If you change from a channel with delay

to a channel with delay set to a different

delay time the delay effect will not spill

between channels.

MP3 / LINE IN

The 3.5mm MP3 / Line In socket (14)

allows the connection of an external audio

source e.g. MP3 or CD player.

HEADPHONES

The 3.5mm Headphone socket (16)

allows the connection of a pair of

headphones. When a jack is inserted into

the headphone socket the unit’s speaker

is muted.

POWER

The Power switch (17) turns the amplifier

on and off. If current settings have not

been stored they will be lost.

RESTORING SETTINGS - WARNING ALL AMP

& FOOTCONTROLLER ALLOCATIONS WILL BE

LOST

To restore the unit to factory settings (see

handbook rear cover) you must hold the

Store switch (12) while powering on the

unit. The Clean/Crunch (3) and

OD-1/OD-2 (5) lights will light orange.

You can then release the Store switch

(12).

Resetting the amplifier will erase all

user Channel presets and all user

Footcontroller allocations, replacing them

with the factory presets.

ENGLISH

0 FX Off

Chorus Speed increases and depth is reduced as knob is

turned clockwise.

Phaser Speed increases as knob is turned clockwise.

Flanger Speed increases, feedback and depth are

reduced as knob is turned clockwise.

Delay Delay level is increased as knob turned

clockwise.

Octave When the FX control is turned fully clockwise

the Octave effect is engaged – producing a

simultaneous note a full octave lower than the

one being played.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Marshall MG15FX Gold Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info