EN
WITH DEFOG FUNCTION MOL
TABL
1) Package contents
2) Safet
3) Installing and using the product
4) Specifications
P
• Bathroom mirror
• Set of screws
• User manual
SAFET
Always take the following precautions into consideration before using the
“Bathroom LED Mirror with Defog Function” hereinafter referred to as the
‘
EX
Remark!
Follow the instructions in the user manual!
W
W
irreversible injury!
W
Risk of electric shock
and/or serious irreversible injury!
W
Risk of suocation. Warning for potential risk of death
and/or serious irreversible injury!
W
Risk of electric shock
device with cloths or cur
this may cause electric shock
to the device. Warning for potential risk of death and/or
serious irreversible injury!
W
Handle with care, fragile goods. Warning for possible
moderate or minor injuries! W
avoid breakage.
Class II
Refers to equipment where protec
shock does not solely rely on basic insulation, but where
additional safet
reinforced insulation are taken, and there is no protective
earthing or reliance upon installation condi
CE marking
Indicates that the product sold in Europe has been
assessed to mee
protection requirement
Instructions for protec
(WEEE, the waste elec
directive)
GENER
• Read the instructions f
this device to other people, please also pass on this manual.
• Only use this device in accordance with the ins
manual.
• This device can be used by children aged 8 and over and people w
restricted physical, sensor
and exper
given instructions abou
potential hazards. Children must not play with the device. Cleaning and
maintenance must not be done by children unless they are over the age
of 8 and under supervision.
• Keep the device and power c
age of 8 years.
• This device is intended for domestic or similar use, not for profe
use.
W Do not leave packaging material lying around
carelessly
children. Risk of suocation!
W
The device contains small part
these par
ELECTRICIT
• Prior to use, check that the mains voltage is the same as the mains
voltage stated on the name plate of the device.
• Make sure your hands ar
or plug.
• Plug the power plug into an electrical outle
at all times.
W Never cover the power plug, cable, electric base or
device with cloths, cur
cause electric shock
• Make sure that the device and power cable do not come into contact
with heat sources, like a hot hob or naked f
• Check the power cord regularly for damage.
• Never use the device if the power cord shows signs of damage, if the
device has fallen on the ground or shows any other signs of damage.
• Switch OFF the device and remove the power plug if you discover any
faults during use, find any signs of damage, are not using the device or
are cleaning it.
• Make sure the power cord cannot be trodden on or pinched.
• Do not allow the power cord to hang over sharp edges and keep it away
from hot objec
• When plugging in the power plug, make sure people cannot
accidentally pull it out or trip over it
• Remove the power plug from the power socket during lightning storms
or if unused for long periods of time.
• When removing the plug from the power socket
not the cable.
• Do not operate the device using an ex
remote control system.
• The use of an ex
USE
• Do not use the device in the vicinit
• Do not leave the device unattended when it is in use.
• This device is not a toy and should be kept under strict super
prevent children from using the device as a toy
• Do not allow children to clean or maintain this device unsupervised.
• Never allow children to use domestic appliances as toys or withou
supervision. Children are unable to judge the hazards associated with
incorrectly using ele
• Children and pets in the vicini
supervised by an adul
• Do not lean on the device.
• Never move the device when it is switched ON or s
OFF the device and only move it when it has coole
• Regularly clean the device thoroughly (see “cleaning and
maintenance”).
• When in use and when stored, do not place any
the device.
• Do not place the device in contac
materials.
• Avoid locations subject to vibrations, cold or humidity.
• Do not expose the de
humidity or corrosive environments.
• Only use the device indoors and not in the vicinit
liquids.
• Do not use the device if i
or any kind of fluid.
• Never immerse the device, cable and power plug in water or any kind
of fluid.
• Do not pick up the device if it has fallen into water or any kind of fluid.
Remove the plug from the power socket imme
device again.
• Do not place the device under any mechanical stress
• Improper use of the device could damage the product
• Please handle the device carefully
height, can damage the device.
• Do not open the casing as this may result in electric shock
• Do not attempt to disassemble or repair the device or modif
manner
• The device must be ser
power supply cord/plug is damaged; liquid has been spilled; object
have fallen into it; it has been expose
dropped or does not operate properly
W Handle with care to avoid breakage. When the mirror
is broken, stop using the device.
• Do not use abrasive cleaning solvents to clean the device.
• Do not use foreign objec
• This device is intended for domestic purposes onl
use.
• The warr
non-compliance wi
liability for damage caused by non-
negligent use or use which does not comply wi
user manual.
• The LEDs cannot be replaced.
W Do not stare at the device’s illuminated LEDs for an
ex
to the eyes. Do not lo
instruments that focus on light rays.
Open the packaging carefully be
the device is complete and undamaged. If any components are missing
or damaged, contact the vendor and do not use the produc
packaging or recycle it in ac
There may be production residues on the device. T
clean the device with a damp cloth and dr
PAR
1. Mirror
2. Defog button
3. Light button
4. LEDs
5. W
6. Power cord
7. Se
8. E
F
1.
4.
2. 3.
BACK:
4.
6.
5. 5.
7. 8.
FIR
• Remove the device and acces
protective f
• Before using the device for the f
• Thoroughly dry the device
• Never use aggressive or abrasive cleaning m
sponge or steel wool; these could damage the device.
WALL MOUNTING
Installation must only be carried out by qualif
assembly can result in severe personal injury and damage.
If you intend to install this device yourself, you must check for ins
such as electrical wiring and plumbing that may be buried inside the wall.
The installer is responsible for verif
total load of the device and wall brackets.
Additional tools (not included) are required for installation.
Do not over-tighten screws.
Use an electronic stud f
mounting. Ensure the w
The device must be fi(5 .
• Mark out where the device should be installed on the wall. Make sure
the openings are levelled and aligned.
• Drill holes into the wall, insert the expanding plugs (8) and fi
of screws (7) .
• Mount the device by sliding the wall mounting brackets (5) onto the
screws (7).
Connec
• Plug the power cord into an electrical outle
all times. Once conne(2) and light
button (3) will light up blue and the device will be in s
• T
mains power
Using the device
LED lights
• T(3) which
lights up white.
