Bedienungsanleitung master DH 26 (Seite 11 von 72) (Alle Sprachen)

588473

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

HUMIDITY GAUGE

•DH 26

Positioned in the front of the appliance. It has a graduated scale

from 1 to 5. When the humidity gauge is set on the minimum

level (1), it means it will work until 80% of relative humidity is

obtained in the room. When it is set on the maximum level (5),

it means the appliance will work until 20% of relative humidity is

obtained in the room. When it is set on “CONT”, the appliance

works continuously no matter what the relative humidity level is.

When it is set on “OFF” the appliance will never start (single pole

switch) (Fig. 4).

•DH 44-62-92

Positioned on the front of the machine. It has a graduated

scale from a minimum of 80% to a maximum of 20% of relative

humidity to be obtained in the room (Fig. 5).

HOUR COUNTER

•DH 26

The hour counter is positioned on the rear of the machine and

indicates the number of hours the appliance has functioned (Fig.

6).

•DH 44-62-92

The hour counter is positioned on the front of the machine and

indicates the number of hours the appliance has functioned (Fig.

6).

FIRST IGNITION

IMPORTANT: In models with dual voltage (...DV), check

the position of the dual voltage switch (220-240V / 110-

120V). If the voltage set does not correspond to the mains

supplied voltage, it is necessary to adjust it. Unscrew the

two securing screws of the cover (Fig. 10), adjust/press

the switch to the correct voltage (Fig. 11) and reassemble

the cover (Fig. 12-13).

Before starting the appliance it must have been in an upright

position (the normal working position) for at least eight hours.

Failure to observe this instruction could cause irreparable

damage to the compressor.

After eight hours the dehumidier can be plugged into a 220-

240 Volt single-phase grounded socket. The “POWER” red

led must switched on to shows that is correctly powered. If

the “WORKING” led is off, turn the humidity gauge knob in a

clockwise direction until it comes on. The “DEFROST” led will

also come on and after about 5 minutes, the dehumidier starts.

If the green “FULL” led is on, the dehumidiers doesn’t start. The

tank must be emptied.

IF THE DEHUMIDIFIER DOES

NOT START OR DOES NOT

DEHUMIDIFY

First of all check the red “POWER” led is on. this shows that

it is correctly powered. Otherwise check if the plug is correctly

connected to the energy supply and if power reach the appliance.

If after these controls the light remains off, take the appliance to

the retailer where it was purchased.

Check the green “FULL” led is off and check the tank is empty.

Check the red “WORKING” led is on, this shows the humidity

gauge required to be in function. When the appliance starts after

a pause because the set humidity level has been reached or

because the tank has been emptied, the “DEFROST” led will

come on, besides the two “POWER” and “WORKING” leds.

They will remain on for about 3 minutes when only the fan will

be working and the compressor will be off.

This cycle is repeated about every 45 minutes to defrost the coil

(evaporator). If the “DEFROST” led remains on for more than

ten minutes take the dehumidier to the retailer where it was

purchased.

If the appliance seems to be working correctly with the

“WORKING” and “POWER” leds on, but no water or very few

is produced, check that the relative humidity in the room is

not lower than 40-45%, otherwise take the dehumidier to the

retailer where it was purchased.

CONNECTION TO A

DISCHARGE PIPE

•DH 26

This dehumidier can be connected directly to a xed discharge

pipe, in which case the tank is removed to enable connecting the

pipe to the coupling.

For the connection, insert the supplied coupling in the right

side of the tank compartment (Fig. 7). Use the supplied rubber

stopper to block the microswitch lever in the left side of the tank

compartment (Fig. 8).

•DH 44-62-92

This dehumidier can be connected directly to a xed discharge

pipe, in which case the tank is removed to enable connecting the

pipe to the threaded male coupling (Fig. 9) (for the model DH 92

remove the plastic connection pre-installed).

For the connection use a pipe with a ¾” female coupling.

PERIODIC MAINTENANCE

The only maintenance that is required is cleaning the lter, the

frequency depending on how dusty the room is and how many

hours the appliance actually works each day.

In normal use it is sufcient to clean the lter once a month, but if

the room is very dusty it should be cleaned more frequently.

The lter is cleaned by washing it under a jet of water in the sink,

owing in the opposite direction to the air ow: the perforated

front panel must face downwards so that the water pushes the

lter against the panel.

After a few years, the hot heat exchanger (condenser) could

need cleaning using compressed air and only a qualied

technician must do this task. This cleaning improves the

appliance efciency and guarantees its long life.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

master DH 26 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info